Panasonic GT32-R User Manual Download Page 72 | Manualshive

Page: 72 / 206

background image

3-10

3.2 Wiring the Power Supply

3.2.1 Wiring the Power supply

The power supply should be wired by securely connecting the terminal on the rear of the main
unit to the terminal.

Use twisted wiring for the power supply

In order to minimize influence from noise, the wiring for the power supply should be twisted.

Insulate the power supply inside a protective circuit



In order to protect the unit against abnormal voltage from the power supply line, the power supply

should be an insulated type, and should be enclosed within a protective circuit.



If a power supply device without an internal protective circuit is being used, power should always be

supplied to the GT series through a fuse or a similar protective device.

Keep the power supply voltage within the operating voltage range

Rated voltage

Operating voltage range

5 V DC

4.5 to 5.5 V DC

24 V DC

21.6 to 26.4 V DC

Keep the power supply wiring separate



Wiring to the GT series, PLC, and other power equipment should have separate wiring systems.

«
...
70
71
72
73
74
...
»

Summary of Contents for GT32-R















































































































































































































Reviews:

No comments

Related manuals for GT32-R

Brand: Dante Pages: 60

Brand: Baaske Medical Pages: 32

Brand: I-Tech Pages: 27

Brand: Daewoo Pages: 10

FusionAmp OLED Display

Brand: Hypex Electronics Pages: 12

Brand: TechLine Pages: 26

Brand: AOC Pages: 40

Brand: WINGTOP Pages: 33

EASY-RTD-DC-43-03B1-00

Brand: Eaton Pages: 91

Brand: AcuRite Pages: 20

Brand: VESTEL Pages: 136

Brand: I-Inc Pages: 23

diamond pro 1000 TFX1105SKTKW

Brand: Mitsubishi Pages: 34

Brand: Idis Pages: 44

ABPM PULSE RATE MONITOR WITH BLUETOOTH

Brand: Gima Pages: 56

Brand: PANL Pages: 2

Rosemount Analytical OPM 4000

Brand: Emerson Pages: 118

Brand: Emerson Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands