Panasonic GT01 User Manual Download Page 132 | Manualshive

Page: 132 / 206

background image

5-10

5.3 Error Codes and How to Handle Them

5.3.1 About Error Codes

When an error occurs in the GT series, an error code displays at the top right of the screen. There are
two types of error codes, GT series error codes and PLC error codes.

For GT02 / GT02L / GT03-E / GT05 / GT12 / GT32 / GT32-R / GT32-E

Code No.

Unit

Reference

**_ _ _ _

GT series

Refer to

“5.3.2 GT Series Error Codes”.

ER_ _ _ _

Note 1)

PLC

Refer to

“5.3.3 When Connected to a FP Series PLC”.

For GT02 / GT02L / GT03-E / GT05 / GT12 / GT32 / GT32-R / GT32-E

Code No.

Unit

Reference

ER_ _ _ _

Note 1)

GT01/GT11/GT21

PLC or GT error
Refer “For GT01, GT11 and GT21”.

Note 1) Some error codes (typical errors only) related to connection with other companies' PLCs are also

introduced. For details, refer to the manual provided by each PLC manufacturer.

5.3.2 GT Series Error Codes

The following error codes are displayed when there is an error in the GT.



GT Unit Errors

For GT01, GT11 and GT21

Code No.

Content

Cause and solution

ER00

BCC error

1) The value of BCC may be incorrect. Check if there is no
calculation mistake.
2) There is a temporary error due to noise, etc. Re-supply power
to the PLC and GT.

ERFF

Time up error
No response from the
PLC.

1) The PLC connection cable is disconnected. Check the
connection cable to make sure it is connected.
2) There is a temporary error due to noise, etc. Re-supply power
to the PLC and GT.

ER21

Data error
A data error occurred
during
communication.

1) An error exists in the communication condition settings.
Check the PLC and GT baud rate and transfer format.
2) There is a temporary error due to noise, etc. Re-supply power
to the PLC and GT.

ER22

Overrun error
The GT cannot
receive data.

The reception buffer in the GT is overflowing.
There could be an error in the PLC
Re-supply power to the PLC and GT.

Note 1)

Duplicated with the PLC error codes. Refer also to “5.3.3

When Connected to a FP Series

«
...
130
131
132
133
134
...
»

Summary of Contents for GT01















































































































































































































Reviews:

No comments

Related manuals for GT01

Brand: GE Pages: 425

Brand: Raymarine Pages: 12

Brand: Jafar Pages: 13

ACTIVE DRIVER M/M 1.1

Brand: DAB Pages: 10

Brand: d&b audiotechnik Pages: 3

ACTIVE DRIVER M/M 1.1

Brand: DAB PUMPS Pages: 38

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands