Panasonic FP-7718 Service Manual Download

Page: 62 / 78

6-3

Unpacking/

Installation

Location

Shipping material/Procedure

Check

Fuser unit

(1) Open the paper exit door.

(2) Open the fuser exit guide plate.

(3) Remove the fuser pressure

release screws. (2 screws)

(4) Close the fuser exit guide plate.

(5) Close the paper exit door.

Developer unit

(1) Swing open the toner bottle/

hopper. (180 degrees)

(2) Turn the developer unit release

lever clockwise.

(3) Remove the recycle solenoid

cover. (1 screw)

(4) Open the waste toner bottle door.

(5) Lower the paper transport.

(6) Remove the drum unit. (1 screw,

1 connector)

(7) Disconnect the TDC connector.

(8) Remove the developer unit.

(Pull out until it stops, then angle

up to remove.)

Note:

Be careful to avoid

damaging the recycle and

toner addition sponge seals.

TDC
connector

Toner bottle
Hopper

Recycle solenoid
cover

Release lever

Waste toner
bottle door

(2)
Tape

Paper transport unit

(1) Open the front cover.

(2) Remove the shipping tape.

Summary of Contents for FP-7718















































































Search results

Summary of Contents for FP-7718

Reviews:

Related manuals for FP-7718

Brands by name

Popular brands

Panasonic FP-7718, Service Manual

Search results

Summary of Contents for FP-7718

Reviews:

Related manuals for FP-7718

Brands by name

Popular brands