background image

2 Mode Noise Filters

 

EXC24CB/CP/CN type

 The pin numbers shown here are for reference purposes only.

Confirm the actual pin number arrangement with the exchanged 
specification documents.

Unit : mm

 Category temperature range

 

–40 

  to  +85 

 Construction

  Circuit configuration (No polarity)

 Dimensions in mm (not to scale)

Part No.

(inch size)

Dimensions

Mass (Weight)

(mg/ pc.)

A

B

C

D

E

F

0.65 ± 0.10

0.35 ± 0.10

3.0

 Ratings

Part number

Impedance

 

(Open mode)

Rated voltage

(V) DC

Rated current

(mA) DC

DC resistance

(Ω) max.

(Ω) at 100 MHz

Tolerance (%)

EXC24C

1.00 ± 0.15

1.25 ± 0.15

0.50 ± 0.10

0.20 ± 0.15

0.3

EXC24CP221U

 

220

350

0.4

EXC24CP121U

 

120

± 25

5

500

EXC24CB221U

 

220

100

0.7

EXC24CB102U

1000

 

50

1.5

Part number

Impedance

 

(Common mode)

Rated voltage

(V) DC

Rated current

(mA) DC

DC resistance

(Ω) max.

(Ω) at 100 MHz

Tolerance (%)

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.

1-Mar-20

EXC24CN601X

600

± 25

5

200

0.9

4

3

1

2

4

3

1

2

C

F

D

A

B

E

Ferrite

Electrode

Inner conductor

Summary of Contents for EXC24CB








Reviews: