6(16,7,9,7<$'-8670(17
6WHS
1.
Turn the sensitivity adjuster fully
counter-clockwise to the mini-
mum sensitivity position (MIN).
2.
In the light received condition,
turn sensitivity adjuster slowly
clockwise and confirm the
point
A
where the sensor en-
ters the “Light” state operation.
3.
In the dark condition, turn sen-
sitivity adjuster further clock-
wise until the sensor enters the
“Light” state operation and then
EULQJLWEDFNWRFRQ¿UPSRLQW
B
where the sensor just returns
to the “Dark” state operation.
If the sensor does not enter the
“Light” state operation even
when the sensitivity adjuster
is turned fully clockwise, this
extreme position is point
B
.
4.
The position at the middle of point
A
and
B
is the optimum sensing position.
A
B
A
B
Optimum
position
Note:
8VHWKHÀDWKHDGVFUHZGULYHUSOHDVHDUUDQJHVHSDUDWHO\WRWXUQWKHDGMXVW
-
er slowly. Turning with excessive strength will cause damage to adjuster.
7
$8720$7,&,17(5)(5(1&(35(9(17,21)81&7,21
Ɣ
R e t o r o r e f l e c t i v e t y p e ,
Spot reflective type and
convergent type sensor in-
corporate this function. Up
to two sets of sensor can
be mounted closely. (Thru-
beam type sensor does not
have this function.)
2 sensor heads can be
mounted adjacently
Note:
,IWZRVSRWUHÀHFWLYHW\SHVHQVRUDUHPRXQWHGIDFLQJHDFKRWKHUWKH\VKRXOGEHDQJOHG
so as not to receive the beam from the opposing sensor or to detect its front face.
*RRG
1RW*RRG
8
32/$5,=,1*),/7(53)(;/2SWLRQDO
2QO\IRUPLUURUUHÀHFWLYHW\SH(;/Ƒ
Ɣ
By installing the polarizing filter
3)(;/
(op-
WLRQDOWRWKHPLUURUUHÀHFWLYHW\SH
(;/
ƑPLUURU
surface object and glossy object are not detected.
Ɣ
Install the polarizing filter to
(;/
Ƒ EHIRUH
mounting
(;/
Ƒ
0RXQWLQJPHWKRG
1.
Face up a large window
of front side of the po-
ODUL]LQJ¿OWHU
2.
Slide from sensing side
and push until it clicks.
Receiving
section
Emitting
section
Slide
Receiving section
Emitting section
5HPRYLQJPHWKRG
1.
Open the side (tabs on
the side) of the polar-
L]LQJ¿OWHUZLWKÀDWEODGH
screwdriver and push
WKHWKHSRODUL]LQJ¿OWHU
tab
Slide
Slightly
open
1RWHV:KHQUHPRYLQJWKHSRODUL]LQJ¿OWHURSHQLQJZLGHO\PDNHVWKH¿OWHU
lose original form and it cannot be use again.
%HVXUHQRWRSHQWKHSRODUL]LQJ¿OWHUE\ÀLQJHULWPD\OHDGLQMXU\
3)
%HVXUHQRWFRQWDFWLQJZLWKZDWHUHWFZKHQWKHSRODUL]LQJ¿OWHULVPRXQWHG
'RQRWFRQWDPLQDWHZLWK¿QJHUSULQWVRUVNLQRLORQWKHSRODUL]LQJ¿OWHU
,QFDVHPRXQWLQJSRODUL]LQJ¿OWHUPDNHVXUHOHDYHPPRUPRUH
EHWZHHQWKLVSURGXFWDQGWKHUHÀHFWLYHPLUURU
5)
(optional.)
,QFDVHLQVWDOOLQJWKHUHÀHFWLYHPLUURUDWFORVHGLVWDQFHWKHDQJXODU
FKDUDFWHULVWLFEHFRPHVQDUURZ&RQGXFW¿QHDGMXVWPHQWRIDQJOHIRU
WKLVSURGXFWRUWKHUHÀHFWLYHPLUURU
Ɣ :KHQXVLQJWKHSRODUL]LQJ¿OWHURSWLRQDOQHHGDW
-
WHQWLRQWRPRXQWUHÀHFWLYHPLUURUVKRZQEHORZ
&RUUHFWPRXQWLQJPHWKRG!
Ɣ 0RXQWWKHUHÀHFWLYHPLUURUKRUL]RQWDOO\RUYHUWLFDOO\
toward
(;/Ƒ
*RRG
&RUUHFWPRXQWLQJPHWKRG!
Ɣ
7KHUHÀHFWLYHPLUURUPXVWQRWEHWLOWWRZDUGWKH
(;/Ƒ
1RW*RRG
63(&,),&$7,216
Ɣ
,QGLYLGXDO6SHFL¿FDWLRQ
Type
Thru-beam type
5HWURUHÀHFWLYHW\SH
Long distance
Model No
(Note 1, 2)
2m cable
(;/
(
-P
)
(;/
(
-P
)
(;/
(
-P
)
Pigtailed
(;/
(
-P
)
-
(;/
(
-P
)
-
(;/
(
-P
)
-
Sensing range
1m
3m
P>ZLWKUHÀHFWLYH
mirror
5)
(ac-
cessory)] (Note 3)
Emission spot size
(typical)
Approx. 6 × 4mm
(vertical × horizon-
tal) (at 1m sensing
range) (Note 4)
Approx. 8 × 5.5mm
(vertical × horizon-
tal) (at 1m sensing
range) (Note 4, 5)
Approx. 6 × 4mm
(vertical × horizon-
tal) (at 1m sensing
range) (Note 6)
Sensing object
ø2mm or more
of opaque object
ø3mm or more
of opaque object
ø25mm or more
o f o p a q u e o r
translucent object
Minimum sensing object
(typical) (Note 7)
ø0.3mm of opaque
object (at 1m sens-
ing range)
-
-
Current consumption
Emitter: less than 10mA, Receiver: less than 10mA
15mA or less
Hysteresis (typical)
-
20% of operation
distance (Note 8)
Interference prevention
function
-
I n c o r p o r a t e d ( 2
heads are possible
to mount adjacently)
Weight
2m cable
Emitter: Approx. 40g, Receiver: Approx. 40g
Approx. 45g
Pigtailed
Emitter Approx. 10g, Receiver: Approx. 10g
Approx. 10g
Accessory
06(;/
(Metal plate): 2 pcs.
5)
5HÀHFWRUSF
06(;/
(Metal plate): 1 pc
Type
6SRWUHÀHFWLYHW\SH
Convergent type
Line spot
Model No
(Note 1, 2)
2m cable
(;/
(
-P
)
(;/
(
-P
)
(;/
(
-P
)
Pigtailed
(;/
(
-P
)
-
(;/
(
-P
)
-
(;/
(
-P
)
-
Sensing range
45 to 300mm (Note 8)
20 to 50mm
(Center 22mm)
(Note 8)
20 to 70mm
(Center 22mm)
(Note 8)
Emission spot size
(typical)
Less than ø1mm
(at 300mm sens-
ing range) (Note 6)
Less than ø1mm
(at 50mm sensing
range) (Note 6)
Approx. 5 × 1mm
(vertical × horizon-
tal) (at 50mm sens-
ing range) (Note 6)
Sensing object
Opaque, translucent or transparent object
Minimum sensing object
(typical) (Note 7)
ø0.01mm of gold wire
-
Current consumption
15mA or less
Hysteresis (typical)
20% of operation distance (Note 8)
Interference preven-
tion function
Incorporated
(2 heads are possible to mount adjacently)
Weight
2m cable
Approx. 45g
Pigtailed
Approx. 10g
Accessory
06(;/
(Metal plate): 1 pc.
Ɣ
&RPPRQ6SHFL¿FDWLRQ
Supply voltage
12 to 24V DC ±10% Ripple P-P 10% or less
Output
131RXWSXWW\SH!
NPN open-collector transistor
• Maximum sink current: 50mA
• Applied voltage: 26.4V DC or less (between output and 0V)
• Residual voltage: 2V or less (at 50mA sink current)
1V or less (at 16mA sink current)
313RXWSXWW\SH!
PNP open-collector transistor
• Maximum source current: 50mA
• Applied voltage: 26.4V DC or less (between output and +V)
• Residual voltage: 2V or less (at 50mA source current)
1V or less (at 16mA source current)
Output operation
Light-ON / Dark-ON
Select by the output operation switching input
Short-circuit protection
Incorporated
Response time
0.5ms or less
Protection
IP67(IEC)
Ambient temperature
-10 to +55°C (No dew condensation or no icing condition)
Storage: -30 to +70°C
Ambient humidity
35 to 85% RH, Storage: 35 to 85% RH
Emitting element
Red semiconductor laser class 1 (IEC / JIS / GB / FDA)
Peak emission wavelength: 655nm,
Maximum output:
0.39mW for
(;/Ƒ
, 0.5mW for
(;/Ƒ
2mW for
(;/Ƒ
, 1mW for
(;/Ƒ
1.3mW for
(;/Ƒ
Material
Enclosure: PBT, Front cover / Light-receiving lens: Acylic
Light-emitting lens: Glass, Indicator: Polyarylate
Cable
2m cable
0.15mm
2
4-core (emitter: 2-core) cabtyre cable, 2m long
Pigtailed
0.15mm
2
4-core (emitter: 2-core) cabtyre cable, 0.2m long
1RWHV7KHPRGHO1RZLWKVXႈ[³
(
´VKRZQRQWKHODEHODႈ[HGLVWKHHPLW
-
ter, “
D
” shown on the label is the receiver.
Emitter:
(;/(
, Receiver:
(;/'
7KHPRGHO1RZLWKVXႈ[³
-P
” is PNP output model.
<Example> PNP output model of
(;/
is “
(;/3
.”
7KHPRGHO1RZLWKVXႈ[³
-C5
” is 5m cable model.
<Example> 5m cable model of
(;/3
is “
(;/3&
.”
7KHPRGHO1RZLWKVXႈ[³
<
´LVQRUHÀHFWRUW\SH
([DPSOH!1RUHÀHFWRUW\SHRI
(;/3
is
“
(;/3<
.”
3) Make sure leave 200mm or more between this product and the re-
ÀHFWLYHPLUURU
5)
(accessory.)
4) The beam of emitter may enter receiver even if it is out of the range
of the emission spot. In case using this devices as cascaded, we
recommend to mount emitters and receivers alternately. In case
mounting this devices in another method, be sure to check the op-
eration with this device.
5) In case the sensing distance is 3m, the emission spot size is 17 ×
11mm (vertical × horizontal) (visual reference value.)
LQFDVHKLJKUHÀHFWLYHREMHFWLVH[LVWLQJEHWZHHQWKLVSURGXFWDQG
the sensing object, this product may detect it.
0DNHVXUHWRFRQ¿UPGHWHFWLRQZLWKDQDFWXDOVHQVRUEHIRUHXVH
8) The sensing distance and the hysteresis of spot refractive type and
¿[HGIRFXVUHÀHFWLYHW\SHLVYDOXHIRUQRQJORVVZKLWHSDSHUî
100mm).
0DNHVXUHWRXVHWKHÀRZLQJFDEOHVZKHQFRQQHFWLQJWKHSLJWDLOHG
type.
6WUDLJKW&DEOH!
CN-24A-C2
(Cable length : 2m),
CN-24A-C5
(Cable length : 5m)
(OERZFDEOH!
&1$/&
(Cable length : 2m),
&1$/&
(Cable length : 5m)
&$87,216
Ɣ
This product has been developed / produced for in-
dustrial use only.
Ɣ
Make sure to carry out wiring in the power supply
OFF condition.
Ɣ
Take care that if a voltage exceeding the rated range
is applied, or if an AC power supply is directly con-
nected, the product may get burnt or damaged.
Ɣ
Take care that short circuit of the load or wrong wir-
ing may burn or damage the product.
Ɣ
Do not run the wires together with high-voltage lines
or power lines, or put them in the same raceway.
This can cause malfunction due to induction.
Ɣ
Verify that the supply voltage variation is within the
rating.
Ɣ
If power is supplied from a commercial switching
regulator, ensure that the frame ground (F.G.) ter-
minal of the power supply is connected to an actual
ground.
Ɣ
In case equipment generating noise (switching regu-
lator, inverter motor, etc.) is used in the vicinity of
this product, connect the frame ground (F.G.) termi-
nal of the equipment to an actual ground.
Ɣ
Do not use during the initial transient time (approx.
50ms) after the power supply is switched ON.
Ɣ
In case the load and this sensor are connected to
different power supplies, be sure to turn ON the
power from the sensor.
Ɣ
Extension up to total 100m or less, is possible with
more than 0.3mm
2
of electric conductor cross-sec-
tional area cable. However, in order to reduce noise,
make the wiring as short as possible.
Ɣ
Make sure that stress by forcible bend or pulling is
not applied to the sensor cable joint.
Ɣ
The cable may break by applying excess stress in
low temperature.
Ɣ
Take care that the sensor is not directly exposed to
fluorescent lamp from a rapid-starter lamp, a high
frequency lighting device or sunlight etc., as it may
DႇHFWWKHVHQVLQJSHUIRUPDQFH
Ɣ ,QFDVHRIPRXQWLQJWKH¿[HGIRFXVUHÀHFWLYHW\SH
WKHVHQVLQJPD\EHLQÀXHQFHGIURPUHÀHFWLYHREMHFW
in the back ground of the sensing object such as
conveyor. In case of sensing the reflective object,
mount the senor with some angles or keep distance
IURPWKHUHÀHFWLYHREMHFWZKHQPRXQWLQJWKHVHQVRU
Ɣ
This product is suitable for indoor use only.
Ɣ 'RQRWDOORZDQ\ZDWHURLO¿QJHUSULQWVHWFZKLFK
may refract light, or dust, dirt, etc., which may block
light, to stick to the emitting / receiving surfaces of
the sensor head. In case they are present, wipe
them with a clean, soft cloth or lens paper.
Ɣ
Do not use this sensor in places having excessive
vapor, dust, etc., or where it may come in contact
with corrosive gas, etc.
Ɣ
Take care that the sensor does not come in contact
with oil, grease, organic solvents such as thinner,
etc., strong acid, or alkaline.
Ɣ
Make sure that the power is OFF while cleaning the
emitting / receiving windows of the sensor head.
Ɣ
This device is using a laser which has high direc-
tional quality. Therefore the beam possibly be out of
alignment by the mounting condition of this device
or distortion of housing etc. Make sure to adjust the
beam axe alignment before use.
Ɣ
Since vibration, impact and ambient temperature af-
fect the sensitivity, the insulation and the sensitivity
adjustment must have some margins.
&(0$5.('352'8&7
Ɣ
The model listed under “
63(&,),&$
-
7,216
” comes with CE Marking.
As for all other models, please contact
RXUVDOHVRႈFH
Panasonic Industrial Devices SUNX Co., Ltd.
https://panasonic.net/id/pidsx/global
Please visit our website for inquiries and about our sales network.
© Panasonic Industrial Devices SUNX Co., Ltd. 2020
PRINTED IN JAPAN
