Panasonic ET-PKR100P Installation Instructions Manual Download Page 1

Page: 1 / 22

TQZJ495-2

Model No.

PKR100P

Installation Instructions

Ceiling Mount Bracket (for portrait)

Thank you for purchasing this Panasonic product.

■ To customers

The “Installation Instructions” is intended for use by installation personnel. Be sure to employ certified personnel to perform

the installation.

After installation, have the installation personnel return these “Installation Instructions” to you, and save it for future use.

When moving or removing the projector, give this manual to the certified personnel and have them perform the procedure.

■ To installation personnel

Read the “Installation Instructions” thoroughly and then perform the operation correctly and safely.

Be sure to read through the section entitled “Read this first!” (page 3) before proceeding with the installation.

After installation, return these “Installation Instructions” to the customer.

Summary of Contents for ET-PKR100P























Search results

Summary of Contents for ET-PKR100P

Reviews:

Related manuals for ET-PKR100P

Brands by name

Popular brands

Panasonic ET-PKR100P, Installation Instructions Manual

Search results

Summary of Contents for ET-PKR100P

Reviews:

Related manuals for ET-PKR100P

Brands by name

Popular brands