9
How to remove the built-in
rechargeable batteries
before disposal of the
epilator
(Fig. 11)
The batteries in this epilator are not
intended to be replaced by consum-
ers. However, the batteries may be
replaced at an authorized service
center. The procedure described
below is intended only for removal
of the rechargeable batteries for the
purpose of proper disposal.
• Always unplug the power cord
from the epilator before disassem-
bling it.
• Always slide the switch to 1 or 2
until the batteries are completely
flat.
• Using a screwdriver, disassemble
the appliance in the following
order.
1. Detach the epilation head
F
a
.
2. Remove the on/off switch
F
b
.
3. Remove the top section
F
c
of
the epilator (3 screws).
4. Remove the two long screws
F
d
.
5. Push in the head release
buttons
F
e
.
6. Push hard on the connector on
the bottom and take out the
drive system
F
f
.
7. Remove the head release
buttons
F
g
(1 screw).
8. Remove the battery holder
section
F
h
(2 screws).
9. Take out the two Ni-MH
batteries
F
i
.
(Please take care not to allow
the batteries to short out on
anything.)
Caution
• Please charge and use the appli-
ance at a temperature of between
5~40°C.
• Never leave children alone with
electrical appliances.
• Never pull the appliance at the
cable out of the socket.
• Never remove or insert the
charging adaptor into the socket
with wet hands.
• Dry this appliance completely
before charging it.
• The appliance and charging
adaptor will become slightly hot
during use or charging, however
this is not a malfunction.
• Store the charging adaptor in a
dry area where it will be protected
from damage.
• Always unplug this appliance from
the electrical outlet immediately
after use.
• Use this appliance only for its
intended use as described in this
manual. Do not use attachments
not recommended by the manufac-
turer.
• Never drop or insert any object
into any opening.
• Keep the device away from
sources of flamability.
• Do not use this appliance with a
damaged or broken epilation/
shaver head.
• Always attach the power cord to
the appliance first, then to the
outlet. To disconnect, turn the
on/off switch to the “0 · charge”
position then remove the power
cord from the outlet.
8
• Turn the switch on and then pour
a little water onto the discs to
create foam.
NOTE: Always check that the
power cord has been removed
before doing this.
• Wash the head with cold or warm
water to remove any hair. (Fig. 8)
NOTE: Do not use hot water to
wash the appliance.
If soap is not completely washed
away, then a white deposit can
accumulate and prevent the
blades from moving smoothly.
• Slide the switch to the “0·charge”
position and wipe the appliance
with a dry cloth.
• After cleaning, put the cap on the
head.
Cleaning your epilator with
the supplied brush
Cleaning of the epilation head
Push the frame release buttons and
remove the frame. (Fig. 7)
Brush the epilation head. (Fig. 9)
While cleaning, you can turn the
epilation discs manually.
Be careful not to break the skin
protector when cleaning.
For disinfection of the epilation
discs please use only pure alcohol.
Attention! Wipe the main body only
with a damp cloth. The use of
alcohol etc. may cause discoloration
of deformation of the main body.
After cleaning, put the cap on the
epilation head.
Cleaning of the shaver head
(ES2047)
Push the frame release buttons and
remove the frame by lifting it from
one side.
Clean with the brush.
Be careful not to apply too much
force to the outer foil.
After cleaning, put the pre-epilation
comb on the shaver head.
Replacing the outer foil of
the shaver head
(Fig. 10)
Never remove the outer foil for
other reason than to change it.
Removing the outer foil
While pushing the outer foil gently
with the fingers, use the fingernail
to release the plastic panel
F
b
on
the blade from the catches
F
a
on
the inside of the frame.
Fitting the new outer foil
Holding the outer foil so that the
surface with the plastic panel
F
b
(i.e.
the surface that will contact the inner
blade) faces upward, insert into the
frame so that the catches
F
a
on the
frame fit into the holes on the foil.
For environmental protection
and recycling of materials
This epilator contains Ni-MH
batteries.
Please make sure that the batteries
are disposed of at an officially
assigned location, if there is one in
your country.
ES2047EU̲1.qxd 06.2.17 17:30 ページ 8
