Panasonic ENW89841A3KF User Manual Download | Manualshive

Page: 39 / 52

background image

User’s Manual

39

Revision 1.3, 2013-08-14

Hardware Description

PAN1322-SPP

ENW89841A3KF

Assembly Guidelines

10.3

Solder Paste Printing

The solder paste deposited on the PCB by stencil printing has to be of eutectic or near eutectic tin leadfree / lead
composition. A no-clean solder paste is preferred, since cleaning of the solder joints is difficult because of the small
gap between the module and the PCB.
Preferred thickness of the solder paste stencil is 100 - 127 µm (4 - 5 mils). The apertures on the solder paste stencil
shall be of the same size as the pads, 0.6 mm.

10.4

Assembly

10.4.1

Component Placement

In order to assure a high yield, good placement on the PCB is necessary. As a rule of thumb the tolerable
misplacement is 150 µm. This means that the PAN1322 module can be assembled with a variety of placement
systems.
It is recommended to use a vision system capable of package pad recognition and alignment that evaluates the
pad locations on the package (in contrast to outline centring). This eliminates the pad to package edge tolerance.
The recommendation is to pick and place the module with a nozzle in the centre of the shield. The nozzle diameter
shall not be bigger than 4 mm.

10.4.2

Pin Mark

Pin 1 (A1) is marked on bottom footprint and on the top of the shield on the module according to

.

Diameter of pin 1 mark on the shield is 0.40 mm.

Pin 1 marking bottom side

PAN1322 01/01

ENW89841A3KF
1302401
FCC ID:T7VEBMU

F2

F3

F4

F5

F6

E1

E2

E3

E4

E5

E6

E7

E8

E9

D1

D2

D3

D4

D5

D6

D7

D8

C1

C2

C3

C4

C5

C6

C7

C8

B1

B2

B3

B4

B5

B6

B7

B8

B9

A2

A3

A4

A5

A6

A7

A8

A1

F9

F7

F1

F8

D9

C9

A9

Pin 1 marking top side

Figure 15

Pin Marking

«
...
37
38
39
40
41
...
»

Summary of Contents for ENW89841A3KF





















































Reviews:

No comments

Related manuals for ENW89841A3KF

Brand: Gantner Pages: 56

Brand: QCON Pages: 4

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: Yardney Pages: 8

Brand: Eaton Pages: 288

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

BT300 BurnerTronic

Brand: Lamtec Pages: 48

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands