manualshive.com logo in svg

Panasonic E18RKUA, Installation Manual, Page: 9 / 17

Share
Download
Panasonic E18RKUA Installation Manual Download Page 9

40 

11.3.3.1  Connect the Cable to the Outdoor Unit 

1. Remove Top panel.
2. Remove Control Board Cover (Resin and

Metal).

3. Remove Plugs.
4. Fix the conduit connectors to the knockout

holes with lock-nuts, then secure them against
the side panel.

5. All wires pass through conduits.
6. Connection cable between indoor unit and

outdoor unit should be UL listed or CSA
approved 4 conductor wires minimum AWG16
in accordance with local electric codes.

7. Wire connection to the power supply

(208/230V 60Hz) through circuit breaker.

o

Connect the UL listed or CSA approved
wires minimum AWG14 to the terminal
board, and connect the other end of the
wires to ELCB / GFCI.

8. Connect the power supply cord and

connection cable between indoor unit and
outdoor unit according to the diagram below.

9. Secure the wire onto the control board with

the holder (clamper).

10. After completing wiring connections, reattach

the control board cover (Metal and Resin) and
the top panel to the original position with the
screws.

11. For wire stripping and connection requirement,

refer to instruction 11.2.5 of indoor unit.

š

Earth lead wire shall be Yellow/Green (Y/G) in
colour and shall be longer than other lead wires
as shown in the figure for electrical safety in case
of the slipping.

11.3.3.2 Piping 

Insulation 

1. Please carry out insulation at pipe connection portion as mentioned in Indoor/Outdoor Unit Installation

Diagram. Please wrap the insulated piping end to prevent water from going inside the piping.

2. If drain hose or connecting piping is in the room (where dew may form), please increase the insulation by

using POLY-E FOAM with thickness 1/4" (6 mm) or above.

Control Board
Metal Cover

Top Panel

Power
Supply
Wires

Lock Nuts

Knockout
Holes

Plugs

Side Panel

Connectors

Control Board
Cover (Resin)

Outdoor Unit

1
2
3

1
2

L1
L2

3

l

a

n

i

m

r

e

T

l

a

n

i

m

r

e

T

Indoor Unit

Disconnect
Switch
Field supply

Grounding wire

Grounding wire min AWG16

* Ensure all connecting wire

between indoor unit and
outdoor unit and power supply
cord are installed in individual
conduit.

Power Supply
Single Phase
208/230V 60Hz
min AWG14

208/230V min AWG16

208/230V min AWG16

208/230V min AWG16

WARNING

This equipment must be properly earthed.

Holder

L1 L2

1

2

3

Power

supply

cord

Indoor &

outdoor

connection

cable

Terminal

Board

Earth wire
longer than
others AC
wires for
safety
reason

Earth wire
longer than
others AC
wires for
safety
reason

Summary of Contents for E18RKUA


















Reviews:

No comments