60
RQT9088
Changing the unit’s settings
Signal Condition
You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
When “Signal Condition” is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [
W X
CH] to select a digital channel. “D” appears on the
unit’s display.
3 Display the Setup menu again (
➡
59).
Press [
3
,
4
] to select “Signal Condition” and press [OK].
The quality and strength of the signal are shown.
Press [
W X
CH] to select the channel.
Signal Quality
Signal Strength
The display for signal strength is grey. “0” means signal strength 0%,
“10” means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥
When the signal is weak:
– adjust the position and direction of the aerial.
– adjust the aerial reception with “DVB Manual Tuning” in the
Setup menu (
➡
59).
– check that the current digital broadcast channel is correctly
broadcasting.
∫
Settings for Analogue Services
Press [OK] to show the following setting.
Manual Tuning
You can delete analogue channels and set the analogue channel
details.
Press [OK] to show Manual Tuning screen.
To delete a programme position
Press [
3
,
4
,
2
,
1
] to select a programme position and press the
“Red” button.
To change the tuning settings for individual programme
position
1
Press [
3
,
4
,
2
,
1
] to select a programme position and press
[OK].
2
Press [
3
,
4
] to select an item and press [
1
].
Below 2 (display red):
The signal quality is so poor that there may
be interference in the pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but
brief interference in the pictures and sound
is possible in isolated case.
Over 5 (display green): Optimum picture and sound quality.
Signal Quality
0
10
Signal Strength
0
10
2 ABC 2W DVB CH30
RETURN
CH +
CH –
Pos
Programme position in the table
(You cannot change the programme position.)
Name
To enter or change the name of a TV
station
Press [
3
,
4
,
2
,
1
] to enter station name
and press [OK].
If the station name needs a blank space,
select the blank between “Z” and “
¢
”.
Channel
To enter newly available TV stations or
change the channel number of an already
tuned TV station
Press [
3
,
4
] or the numbered buttons to
enter the channel number of the desired TV
station.
Wait a few moments until the desired TV
station has been tuned.
After the desired TV station is tuned, press
[OK].
Fine Tuning
To obtain the best tuning condition
Press [
3
,
4
] to adjust the best tuning
condition and press [OK].
≥
Press [
1
] to return to “Auto”.
Mono
To select the type of sound to be recorded
Press [
3
,
4
] to select “On” if the stereo
sound is distorted due to inferior reception
conditions, or if you want to record the normal
(mono) sound during a stereo, bilingual
broadcast, and press [OK].
Manual Tuning
Pos Name Ch
Pos Name Ch
Delete
1 ARD 4
2 ZDF 2
3 N3 5
4 HR3 8
5 BR3 10
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
OK
RETURN
SELECT
Pos
Name
Channel
Fine Tunin
g
1
4
Auto
RETURN : leave
Manual
Tunin
g
ARD
Mono
Off
RETURN
SELECT
DMREX78&88GN-RQT9088-L_eng.book 60 ページ ２００８年４月１日 火曜日 午後６時３８分
