E
N
G
L
I
S
H
30
E
N
G
L
I
S
H
29
Installation Guide
Definition of Terms
CX-DVP292N
CX-DVP292N
32
33
Digital audio output connector (Optical)
The digital audio output connector (optical)
converts electrical signals into optical signals and
transfers them to the amplifier. Consequently, it has
a number of features including its immunity from
electrical interference from external sources and its
ability to prevent the generation of noise and its
minimal effect on the external environment.
Dolby Digital
Dolby Digital is a digital sound compression
technique developed by the Dolby Laboratories
Licensing Corporation.
Supporting 5.1-channel surround sound, as well as
stereo (2-channel) sound, this technique enables a
large quantity of sound data to be efficiently
recorded on a disc.
Interactive DVD
An interactive DVD is DVD software which includes
multiple angles, multiple plot endings, etc.
Letterbox screen
This refers to a screen on which the playback
picture of wide-screen DVDs or Video CDs appears
with black bands running along the top and bottom.
Linear PCM audio (LPCM)
This refers to a signal recording format used in
CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 48 kHz/16 bit up to 96 kHz/
24 bit, thus achieving higher quality audio than that
of CDs.
MPEG
MPEG is an international standard format for the
compression of motion video as defined by the
Motion Picture Experts Group, a working
committee which functions under the auspices of
the International Standardization Organization and
International Electrotechnical Commission. The
Group established the MPEG 1 standard in 1991
and the MPEG 2 standard in 1994. MPEG 2 builds
on MPEG 1 with many improvements, and it yields
a higher picture quality level.
Pan & Scan screen
This refers to a screen on which the playback
picture of wide-screen DVDs or Video CDs is cut off
at the left and right sides.
Playback control (Video CD)
If the Video CD has “With Playback Control” or
others written on the disc surface or on the jacket,
the scenes or information to be viewed (or listened
to) can be selected interactively with the screen by
looking at the menu shown on the screen.
In these instructions, playback using the menu
screen is referred to as the “menu play” for video
CDs. This player supports Video CDs with playback
control.
Title, Chapter (DVD)
DVDs are divided into some large sections (titles)
or some small sections (chapters). Each section is
numbered; these numbers are called “Title number”
or “Chapter number”.
Track (Video CD/CD)
Video CDs or CDs are divided into some sections
(tracks). Each section is numbered; these numbers
are called “Track number”.
Title 2
Title 1
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D sym-
bol are trademarks of Dolby Laboratories.
Confidential unpublished works.
C
1992 – 1997 Dolby Laboratories. All rights
reserved.
Chapter 1
Chapter 2
……
Chapter 1 ……
Track 1
Track 3
Track 2
……
Track
❐
Preparation
≥
We strongly recommend that you wear
gloves for installation work to protect
yourself from injuries.
Caution:
≥
Do not disconnect the battery terminals of a
car with a trip or navigational computer
since all user settings stored in memory will
be lost. Instead take extra care with
installing the unit to prevent shorts.
Note:
≥
Consult a qualified servicing engineer
or your dealer for information on
installing this player to a dashboard.
≥
Disconnect the cable from the negative
-
battery
terminal (see caution below).
≥
Unit should be installed in a horizontal position
with the front end up at a convenient angle, but
not more than 30
o
.
Less than 30
x
❐
Installation Hardware
No.
Cord clamp
6
Diagram
Item
Q’ty
4
1
2
3
4
5
Tapping screws
(5 mm
·k
16 mm)
Screw with washers
(5 mm
·k
6 mm)
4
2
1
1
L-shaped brackets
Power connector
Clamp connector
1
Caution:
≥
All other installation methods required the
use of dedicated metal fittings. Consult
with a qualified servicing engineer or your
dealer if other methods are required.
≥
When drilling holes in the car, make sure
that you do not damage any pipes or wiring
on the underside of the car.
≥
When installing the unit, make sure that
the cord is positioned in a location where
it will not pinched or damaged when the
seat slides forward or backward.
The diagram below shows an example in which this
unit is installed to the floor. Consult a qualified ser-
vicing engineer or your dealer for information on
installing this unit to a different location.
When Installing the unit with the
L-shaped brackets
3
a) Attach the L-shaped brackets
3
on
both sides of unit with the screw with
washers
2
.
b) Install the unit with tapping screws
1
.
Unit
3
L-shaped bracket
2
4 screws with washers
(5
mm
·k
6 mm)
1
4 tapping screws
(5 mm
·k
16 mm)
❐
How to install the unit
