Panasonic CT30WC14J - 30" COLOR TV Service Manual Download Page 91

Page: 91 / 296

file:///C:/AA/Nowy%20folder/NA/CT-32HL44J/SVC/s1001000000.html

Dress coil as was on the original CRT.

8. Replace the components on CRT neck and reinstall into cabinet. Verify that all ground wires

and circuit board plugs get connected.

NOTE

Reuse all the clampers and mounting brackets from the degauss coil and screen, and when

remounting the degauss coil assure that is not touching the speakers, this can be done by

placing some tape, this may cause mask vibration. The mounting brackets andclampers are not

supplied with the replacements.

IMPORTANT NOTICE

When ordering the CRT, please order CRT and CRT kit also. Please see parts list section for

part numbers

TOP

file:///C:/AA/Nowy%20folder/NA/CT-32HL44J/SVC/s1001000000.html (2 z 2) [2008-04-17 10:12:10]

Summary of Contents for CT30WC14J - 30" COLOR TV









































































































































































































































































































Search results

Summary of Contents for CT30WC14J - 30" COLOR TV

Reviews:

Related manuals for CT30WC14J - 30" COLOR TV

Brands by name

Popular brands

Panasonic CT30WC14J - 30" COLOR TV, Service Manual

Search results

Summary of Contents for CT30WC14J - 30" COLOR TV

Reviews:

Related manuals for CT30WC14J - 30" COLOR TV

Brands by name

Popular brands