manualshive.com logo in svg

Panasonic CS-Z25UD3RAW, Operating Instructions Manual, Page: 22 / 24

Share
Download
Panasonic CS-Z25UD3RAW Operating Instructions Manual Download Page 22

22

Troubleshooting

When...

■

  Conducting a seasonal inspection after extended non-use

• Check that there is no obstruction around the air inlet and outlet vents.
• These units are mounted inside the ceiling. It uses external air intake vent and air outlet vent 

to operate. Please consult your nearest dealer for seasonal inspection.

• After 15 minutes of operation, it is normal to have the following temperature difference 

between the air inlet and outlet vents: 

COOL: 

≥

8°C / 14.4°F

  

HEAT: 

≥

14°C / 25.2°F

■

  The units are not going to be used for a long period of time

• Activate HEAT mode for 2~3 hours to remove moisture left in the internal parts thoroughly to 

prevent mould growth.

• Turn off the power supply and unplug.

NON SERVICEABLE CRITERIA

TURN OFF THE POWER SUPPLY AND UNPLUG then please consult an authorised 

dealer when in following conditions:

• Abnormal noise during operation.
• Water/foreign particles have entered the remote control.
• Water leaks from Indoor unit.
• Circuit breaker switches off frequently.
• Power cord becomes unnaturally warm.
• Switches or buttons are not functioning properly.

Summary of Contents for CS-Z25UD3RAW

























Reviews:

No comments