Panasonic CS-PW12CKE Service Manual Download Page 2

Page: 2 / 65

1 Functions

Remote Control

Operation OFF / ON

OFF / ON

Room Temperature Setting

TEMP.

Operation Mode Selection

AUTO

Automatic Operation Mode

HEAT

Heating Operation Mode

COOL

Cooling Operation Mode

DRY

Soft Dry Operation Mode

MODE

TIME

Time / Timer Setting

Hours and minutes setting.

Indoor Fan Speed Selection

FAN SPEED

FAN

Low Fan Speed

FAN

Medium Fan Speed

FAN

High Fan Speed

AUTO

Automatic Fan Speed

FAN

Vertical Airflow Direction Control

24-hour, OFF / ON Real Timer Setting.

ON-TIMER

OFF-TIMER

Timer Operation Selection

SET

CANCEL

Timer Operation Set / Cancel

ON Timer and OFF Timer setting and
cancellation.

AIR SWING

AUTO

Automatic Vertical Airflow
Direction Control

MANUAL

Vertical Airflow Direction
Manual Control (5 stages of
adjustment)

Heating, Cooling, Soft Dry Operation.

Temperature Setting (16

C to 30

Automatic Operation

Operation with 2

C higher than

standard temperature.
Operation with standard temperature.
Operation with 2

C lower than

standard temperature.

•
•
•

•

•
•
•

•

•
•

•

CS-PW9CKE / CU-PW9CKE / CS-PW12CKE / CU-PW12CKE

Panasonic ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

Summary of Contents for CS-PW12CKE


































































Search results

Summary of Contents for CS-PW12CKE

Reviews:

Panasonic CS-PW12CKE, Service Manual, Page: 2 / 65

Search results

Summary of Contents for CS-PW12CKE

Reviews: