Panasonic CS-ME10DTEG Service Manual Download Page 62

Page: 62 / 136

8.3.1.3. Cooling Operation

8.3.1.3.1. Thermostat control

•

Compressor is OFF when Intake Air Temperature - Internal Setting Temperature < -1.5°C.

•

Compressor is ON after waiting for 3 minutes, if the Intake Air Temperature - Internal Setting Temperature > Compressor OFF
point.

8.3.1.4. Soft Dry Operation

8.3.1.4.1. Thermostat control

•

Compressor is OFF when Intake Air Temperature - Internal Setting Temperature < -2.0°C.

•

Compressor is ON after waiting for 3 minutes, if the Intake Air Temperature - Internal Setting Temperature > Compressor OFF
point.

8.3.1.5. Heating Operation

8.3.1.5.1. Thermostat control

•

Compressor is OFF when Intake Air Temperature - Internal Setting Temperature < +2.0°C.

•

Compressor is ON after waiting for 3 minutes, if the Intake Air Temperature - Internal Setting Temperature > Compressor OFF
point.

Summary of Contents for CS-ME10DTEG









































































































































Search results

Summary of Contents for CS-ME10DTEG

Reviews:

Panasonic CS-ME10DTEG, Service Manual, Page: 62 / 136

Search results

Summary of Contents for CS-ME10DTEG

Reviews: