4
3
8
9
CQ-VD7001U
CQ-VD7001U
Installation Guide
(continued)
English
English
❏
Installation Hardware
(For Installation)
❏
Installation Hardware
(For Wiring)
Note:
¡
The number in parenthesis underneath each accessory
part name is the part number for maintenance and ser-
vice.
¡
Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
Qty.
Diagram
Item
No.
Trim Plate
<YEP9FZ2739>
q
1
Mounting Collar
<YEFG012694>
w
1
Mounting Spring
<YEFX0052714>
e
2
Qty.
Diagram
Item
No.
Power Connector
<YAJ024C113A>
!3
1
Reverse Extension Cord
<WAVS05M6000T>
!4
1
Clip Connector
<YEAT034C012>
!5
1
Rear Support Strap
<YEFG04019>
<ZZBISVD7001B>
u
1
Round Head Screw
(5 mmø x 6 mm)
i
2
Flat-Head Screw
(5 mmø x 6 mm)
o
4
Round Head Screw
(4 mmø x 3 mm)
!0
4
<ZZBISVD7001A>
Mounting Bolt (5 mmø)
r
1
Tapping Screw
(5
mm
ø
x 16 mm)
t
1
Hex. Nut (5
mm
ø)
y
1
<ZZBISVD7001E>
Spacer
!1
2
Double-Faced Adhesive Tape
!2
1
set
❏
Before Installation
Warning
¡
Do not install the monitor in a location which
obstructs driving, visibility or which is prohibited
by applicable laws and regulations.
If the monitor
is installed in a location which obstructs forward vis-
ibility or operation of the air bag or other safety
equipment or which interferes with operation of the
car, it may cause an accident.
¡
Never use bolts or nuts from the car's safety devices
for installation. If bolts or nuts from the steering
wheel, brakes or other safety devices are used for
installation of the monitor, it may cause an accident.
¡
Attach the wires correctly. If the wiring is not cor-
rectly performed, it may cause a fire or an accident.
In particular, be sure to run and secure the lead wire
so that it does not get tangled with a screw or the
moving portion of a seat rail.
¡
Use with 12 V DC negative ground car. This unit is
only for use with a 12 V DC negative ground car. It
cannot be used in large trucks or diesel cars which
are 24 V DC cars. If it is used in the wrong type of
car, it may cause a fire or an accident.
❏
Required Tools
You’ll need a screwdriver and the following:
12 V DC
Test Bulb
Electrical
Tape
Side-Cut
Pliers
Caution
¡
Use the specified fuse. Be sure to always use the
specified fuse. If a fuse other than the specified
fuse is used, it may cause a fire or an accident.
¡
Do not damage the cord by pinching or pulling it.
Do not pull or damage the cord. If the cord is not
treated properly, it will short out or be severed and
may cause a fire or an accident.
❏
Dashboard Specifications
❏
Identify All Leads
The first step in installation is to identify all the car wires
you’ll use when hooking up your LCD monitor.
As you identify each wire, we suggest that you label it
using masking tape and a permanent marker. This will help
avoid confusion when making connections later.
Note:
¡
Do not connect the power connector to the display
unit until you have made all connections. If there are
no plastic caps on the hooking wires, insulate all
exposed leads with electrical tape until you are ready
to use them. Identify the leads in the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug (leav-
ing the leads as long as possible) so that you can work
with individual leads. Turn the ignition on to the accessory
position, and ground one lead of the test bulb to the chas-
sis.
Touch the other lead of the test bulb to each of the exposed
wires from the cut radio connector plug. Touch one wire at a
time until you find the outlet that causes the test bulb to
light.
Now turn the ignition off and then on. If the bulb also turns
off and on, that outlet is the car power lead.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for radio
(RADIO) accessory (ACC) or ignition (IGN).
Battery Lead
If your stereo unit has a yellow lead, you will need to
locate the car's battery lead. Otherwise you may ignore
this procedure. (The yellow battery lead provides continu-
ous power to maintain a clock or other functions.)
THICKNESS
MIN. 4.75 mm {3/16
”
}
MAX. 5.56 mm {7/32
”
}
53 mm {2-3/32
”
}
182 mm {7-5/32
”
}
