Panasonic AWRP301 - PAN/TILT CONTROL PAN, Service Manual

Page: 6 / 22

4
1 +5V
2 ZOOM
3 FOCUS
4 TILT
5 PAN
6 GND
7 SPEED
8 IRIS
Ground GND
1
2
3
4
6
7
Ground
5
8
Example of auxillary
control circuit
Note: Make sure that the lens and pan/tilt head stop
at the center point of the zoom, focus, pan and tilt controls
(or at the lever reset position if the controls have a lever reset function).
Iris control
Zoom
control Pan
control
Tilt
control
Focus
control
SPEED switch
100
Ω
10K
Ω
10K
Ω
10K
Ω
10K
Ω
6.8K
Ω
20K
Ω
6.8K
Ω
100
Ω
100
Ω
100
Ω
8-pin DIN connector
pin assignment
(as viewed from the
rear of the control panel)
@5
Pan/tilt Control Output Connector
[TO MULTI PORT HUB, PAN/TILT CONTROL OUT] (RJ-45 8-pin Modular Jack)
Connect it to pan/tilt control input connector [PAN/TILT CONTROL IN] on the pan/tilt head with a 10BASE-T straight cable (UTP
category 5 or equivalent), which may be extended up to 500 meters.
S P E E D . S W
C H A N G E
L O W H I G H
Z O O M
R E V E R S E
N O R R E V
Z O O M / F O C U S
E X C H A N G E
O F F O N
F O C U S
R E V E R S E
N O R R E V
T I LT
R E V E R S E
N O R R E V
PA N
R E V E R S E
N O R R E V
■
Front Panel
@6
Speed Switch Changing Switch
[SPEED SW CHANGE, LOW/HIGH]
Changes the polarity of SPEED Switch
!1
. If ZOOM
lever
!8
, FOCUS Lever
!9
, or PAN/TILT Lever
@0
is
moved while keeping SPEED Switch
!1
depressed, the
corresponding operation takes place at low speed, pro-
vided that SPEED SW CHANGE Switch
@6
is in the
LOW position. If one of these levers is moved with
SPEED Switch
!1
depressed when SPEED SW
CHANGE Switch
@6
is in the HIGH position, the corre-
sponding operation takes place at high speed.
The speed polarity can also be changed by pressing
MEMORY Switch
o
while keeping SPEED Switch
!1
depressed. When this step is taken again, the original
speed polarity is restored. Take this step if it is difficult
to shift SPEED SW CHANGE Switch
@6
because this
control panel is mounted on a console or the like.
@7
Zoom Reverse Switch
[ZOOM REVERSE, NORM/REV]
Changes the operating direction of ZOOM Lever
!8
. The
lens zoom moves toward TELE when ZOOM Lever
!8
is moved toward TELE, or toward WIDE when it is
moved toward WIDE, provided that ZOOM REVERSE
Switch
@7
is in the NOR position. When ZOOM
REVERSE Switch
@7
is set to the REV position, lens
zoom operation takes place in the opposite direction.
With ZOOM REVERSE Switch
@7
in the REV position,
the operating directions shown on the panel are
reversed. In this case, paste the supplied seal on the
panel.
@8
Zoom/Focus Exchange Switch
(ZOOM/FOCUS EXCHANGE, ON/OFF]
ZOOM Lever
!8
and FOCUS Lever
!9
exchange their
function between them when this switch is set to the ON
position. Unless this exchange is needed, keep the
switch in the OFF position.
With ZOOM/FOCUS EXCHANGE Switch
@8
in the ON
position, the operations shown on the panel do not
agree with the indications on the panel. In this case,
paste the supplied seal on the panel.