Panasonic AV-HS6000, Operating Manual

Page: 122 / 173

– 122 –
Chapter 7 CONFIG Menu — Setting the operation mode
- 50i: Max. 39s24f
- 50p: Max. 19s49f
- 24PsF: Max. 41s15f
- 23.98PsF: Max. 41s15f
f
The time that can be set in [Frame] is between 0 and 999 frames.
FTB (Fade to Black)
For DSKPGM1 and DSKPGM2 outputs, fade out from the program image to the black background screen, and fade in from the black ground screen
to the program image. While the settings and transition are performed by the menu, use the macro memory to assign to certain buttons to execute
transition.
1
Select the <CONF> button →
[OPERATE]
→
[Transition] tab.
2
Select an item in [Source] in the [FTB] column.
f
Select the image for fading out.
[Still1] ‑ [Still4]
Uses still image video memory (Still1 to Still4).
[Clip1] ‑ [Clip4]
Uses moving image video memory (Clip1 to Clip4).
[CBGD1], [CBGD2] Uses the color background.
[White] Uses the white background.
[Black] Uses the black background.
3
Set [Time] in the [FTB] column.
f
Set the transition time.
4
Set [FTB On] in the [FTB] column.
f
When [FTB On] is selected, the screen fades out to the image selected in the step
2
at a specified transition time.
If [FTB On] is selected when the image selected in the step
2
is on the screen, the screen fades in to the program image.
If [FTB On] is selected during transition, the transition direction is reversed.
@ @
NOTE
t
If an item other than [White] or [Black] is selected in [Source] in the [FTB] column, the corresponding crosspoint buttons will light in red while [FTB On]
is set.
AUX1 to AUX4 bus transitions
In the AUX1 to AUX4 buses, MIX transition is available.
1
Select the <CONF> button →
[OPERATE]
→
[Transition] tab.
2
Select an item in [AUX1] to [AUX4] in the [AUX Trans] column.
[Off] Disables the MIX translation.
[On] Enables the MIX translation.
3
Set [AUX1] through [AUX4] in the [Trans Time] column.
f
Set the transition time.
r
AUX bus transition operation
Lights in the Preset tally color
Blinks in the Low tally color (during transition)
If [AUX1] to [AUX4] are set to [On] in the [AUX Trans] column, select the source signal that is changed by the corresponding KEY bus crosspoint
buttons.
At this time, the MIX transition is performed at the transition time specified in [AUX1] to [AUX4] in the [Trans Time] column.
During transition, KEY crosspoint buttons denoting the transition source lights in the Preset tally color, and the KEY bus crosspoint buttons denoting the
transition target source lights in the Low tally color.
When the transition is completed, the transition source button goes off, and the transition target button lights in the Low color.
When another signal is selected during transition, the transition processing continues from that midway point.
Switching the ME area in the Control Panel AV‑HS60C1/AV‑HS60C2
Switch the ME1 and ME2 in the Control Panel AV-HS60C1/AV-HS60C2.
@ @
NOTE
t
This function will be available in V2.00.00 or higher.
f
The following figure shows the area that can be switched.