Panasonic AG-HSC1UP Operating Instructions Manual Download Page 33

Page: 33 / 140

VQT1F36

Setup

The power can be turned on and off with the LCD
monitor when the mode dial is set to

To turn on the power

Open the LCD monitor.

The status indicator

lights and the power turns

on.

To turn off the power

Close the LCD monitor.

The status indicator

goes off and the power

turns off. (If [QUICK START] (

33) is set to

[ON], the unit goes into quick start standby mode
and the status indicator lights green.)

≥

The power will not turn off while recording a
motion picture even if the LCD monitor is
closed.

Quick start

When quick start is ON the battery power is still
being consumed, even when the LCD monitor is
closed.
This unit will resume recording/pause mode
about 1.7 seconds after the LCD monitor is
reopened.

≥

When in quick start standby mode about
70% of the power used in recording pause
mode is being consumed, so the recording
time will be reduced.

≥

This is only activated in the following case.

– When the mode dial is set to

and an

SD card is inserted.

Press the MENU button, then
select [SETUP]

[QUICK START]

[ON] and press the cursor

button.

Close the LCD monitor while the
mode dial is set to

The status indicator

lights green and the

unit goes into quick start standby mode.

≥

The lens cover does not close.

Turning the power on and off with
the LCD monitor

Set the mode dial to OFF when this unit is not
being used.

VQT1F36_ENG_PP.book 33 ページ２００７年２月２６日　月曜日　午前１１時２９分

Summary of Contents for AG-HSC1UP













































































































































Search results

Summary of Contents for AG-HSC1UP

Reviews:

Related manuals for AG-HSC1UP

Brands by name

Popular brands

Panasonic AG-HSC1UP, Operating Instructions Manual

Search results

Summary of Contents for AG-HSC1UP

Reviews:

Related manuals for AG-HSC1UP

Brands by name

Popular brands