background image

22

The following symptoms do not indicate malfunction.

Symptom

Cause

POWER indicator blinks before the unit is 
switched on.

• This is a preliminary step in preparation for the 

operation when the ON timer has been set.

• When ON Timer is set, the unit may start earlier (up 

to 30 minutes) before the actual set time in order to 
achieve the desired temperature on time.

POWER indicator blinks during HEAT mode 
with no warm air supply (and flap is closed).

• The unit is in defrost mode (and AIR SWING is set to 

AUTO).

TIMER indicator is always on.

• The timer setting repeats daily once set.

Operation is delayed a few minutes after 
restarting.

• The delay is a protection to the unit’s compressor.

Indoor fan stops occasionally during heating 
operation.

• To avoid unintended cooling effect.

Indoor fan stops occasionally during automatic 
fan speed setting.

• This helps to remove the surrounding odour.

Airflow continues even after operation
has stopped.

• Extraction of remaining heat from the indoor unit 

(maximum 30 seconds).

The room has a peculiar odour.

• This may be due to damp smell emitted by the wall, 

carpet, furniture or clothing.

Cracking sound during operation.

• Changes of temperature caused the expansion/

contraction of the unit.

Water flowing sound during operation.

• Refrigerant flow inside the unit.

Mist emerges from indoor unit.

• Condensation effect due to cooling process.

Outdoor unit emits water/steam.

• Condensation or evaporation occurs on pipes.

Louder noise at outdoor unit during early 
operation of i AUTO-X.

• The compressor and fan rotate at higher speed to boost 

cooling performance during initial operation.

Discoloration of some plastic parts.

• Discoloration is subject to material types used in plastic 

parts, accelerated when exposed to heat, sun light, UV 
light or environmental factor.

Check the following before calling for servicing.

Symptom

Check

Operation in HEAT/COOL mode is not working 
efficiently.

• Set the temperature correctly.
• Close all doors and windows.
• Clean or replace the filters.
• Clear any obstruction at the air inlet and air outlet 

vents.

Noisy during operation.

• Check if the unit has been installed at an incline.
• Close the front panel properly.

Remote control does not work.
(Display is dim or transmission signal is weak.)

• Insert the batteries correctly.
• Replace weak batteries.

The unit does not work.

• Check if the circuit breaker is tripped.
• Check if timers have been set.

The unit does not receive the signal from the 
remote control.

• Make sure the receiver is not obstructed.
• Certain fluorescent lights may interfere with signal 

transmitter. Please consult authorised dealer.

Troubleshooting

ACXF55-18740_FC0118-0.indb   22

ACXF55-18740_FC0118-0.indb   22

12/21/2017   10:05:27 AM

12/21/2017   10:05:27 AM

Summary of Contents for Aero CS-PE12UKV-6





























Reviews: