manualshive.com logo in svg

Pan Acoustics P 08-Pi, Manual

Share
Download
Pan Acoustics P 08-Pi Manual Download Page 11

© Pan Acoustics GmbH   

 V 1.0    

Page 11 of 24     

Manual 

                                                                                                

The low-impedance variant of the loudspeaker P 08-Pi | IP65 is equipped with a 2-pin connection 

cable of 5 m length. The connection cable is permanently connected to the loudspeaker at the factory 

and can be shortened to the required length. In addition to the connection cable, the loudspeaker P 

08-Pi | IP65 features a maintenance-free pressure equalisation element for weather protection.

8.2.2. P 08-Pi | IP65 (low impedance)

Connection of the loudspeaker to the audio network:

• 

shorten the connection cable to the desired or required length

• 

remove approx. 5 cm of cable sheath at the end of the cable and expose the wires

• 

strip the individual wires

• 

fi t the wires with wire end ferrules

• 

connect the connection cable to the audio network according to the technical rules

Connection cables must not be used for fi xing or suspending loudspeakers.

WARNING

Summary of Contents for P 08-Pi

























Reviews:

No comments

Brands by name

Popular brands

Load more brands