Pan Acoustics AMT P 04-AMT Manual Download Page 14

© Pan Acoustics GmbH   

 V 1.0    

Page 14 of 18

Manual

14. Warranty

Pan Acoustics GmbH

Schweigerstr. 13d

38302 Wolfenbüttel

Germany

Tel.: +49 (0) 5331 900 95 70

Fax:  +49 (0) 5331 900 95 79

E-mail: [email protected]

15. Contact address

Pan Acoustics 

stands by its products and gives up to 

10 years warranty

 on 

its loudspeakers for 

any material or manufacturing defects. New products manufactured in accordance with protection 

classes  IP54  and  IP65  as  well  as  digital  audio  interfaces  (Dante

®

)  from  Audinate  Pty  Ltd  and  re-

chargeable batteries are excluded from the 10-year warranty. A warranty period of 3 years is granted 

for loudspeakers in accordance with protection classes IP54 and IP65. For further information on the 

warranty, please refer to the Pan Acoustics warranty conditions.

https://www.pan-acoustics.de/en/service/warranty

16. Mounts

Recommended mounts for mounting products from the Pan AMT series on walls and ceilings or for 

mobile use include:

Tripod mount

Wall mount, TWM II

Wall/ceiling mount P/PB 04 with 

access protection

Stand for P/PB xx loudspeaker 

systems

Wall mount, TWM III

Ceiling mount (BK)

Depending on the length and weight of the loudspeaker, a corresponding number of mounts must be 

used and, if necessary, additional measures for stability or fall protection must be taken.

Information on additional measures or the number of mounts to be used can be found in the manual 

of the corresponding accessory. If you have any technical questions, you can also contact our support 

team at [email protected].

NOTICE

Summary of Contents for AMT P 04-AMT



















Reviews: