PaloAlto Networks PA-1400 Series Hardware Reference Manual Download Page 40

Page: 40 / 46

PA-1400 Series Firewall Specifications

PA-1400 Series Environmental Specifications

The following table describes PA-1400 Series firewall environmental specifications.

Specification

Value

Operating temperature range

32ºF to 104ºF (0ºC to 40ºC)

Non-operating temperature

-4ºF to 158ºF (-20ºC to 70ºC)

Humidity tolerance (non-condensing)

Operating and non-operating relative

humidity

—10% to 90%

Airflow

Front-to-back

Maximum BTU/hr

819BTU/hr

Electromagnetic Interference (EMI)

FCC Class A, CE Class A, VCCI Class A

Acoustic noise

•

Average

—51 dB(A)

•

Maximum

—65 dB(A)

Maximum operating altitude

10,000ft (3,048m)

PA-1400 Series Next-Gen Firewall Hardware Reference

2022 Palo Alto Networks, Inc.

Summary of Contents for PA-1400 Series















































Search results

Summary of Contents for PA-1400 Series

Reviews:

Related manuals for PA-1400 Series

Brands by name

Popular brands

PaloAlto Networks PA-1400 Series, Hardware Reference Manual

Search results

Summary of Contents for PA-1400 Series

Reviews:

Related manuals for PA-1400 Series

Brands by name

Popular brands