3
SAFETY RULES (CONTINUED)
•
Keep tool clean for safest operation.
•
Remove adjusting tools. Form habit of checking to see that
adjusting tools are removed before turning machine on.
•
Keep all parts in working order. Check to determine that the
guard or other parts will operate properly and perform their
intended function.
•
Check for damaged parts. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting and any
other condition that may affect a tool’s operation.
•
A guard or other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs. (Use
the parts list to order replacement parts.)
KNOW HOW TO USE TOOL
•
Use right tool for job. Do not force tool or attachment to do a
job for which it was not designed.
•
Disconnect tool from power when changing accessories such
as grinding wheels, buffing wheels and the like.
•
Avoid accidental start-up. Make sure that the switch is in the off
position before plugging in.
•
Do not force tool. It will work most efficiently at the rate for
which it was designed.
•
Keep hands away from moving parts and grinding surfaces.
•
Never leave a tool running unattended. Turn the power off and
do not leave tool until it comes to a complete stop.
•
Do not overreach. Keep proper footing and balance.
•
Never stand on tool. Serious injury could occur if tool is tipped
over.
•
Know your tool. Learn the tool’s operation, application and spe-
cific limitations.
•
Use recommended accessories. Understand and obey all safety
instructions supplied with accessories. The use of improper
accessories may cause risk of injury to persons.
•
Do not over tighten wheel nut. Replace cracked wheel immedi-
ately. Use only flanges supplied with the grinder.
•
Adjust distance between wheel and tool rest to maintain
1
/
16
” or
less gap.
•
Handle the workpiece correctly. Whenever possible, use tool
rest to support workpiece during grinding operation. Turn tool
off if it jams.
•
Always use guards and eyeshields.
•
Clean grinding dust from beneath tool frequently.
ASSEMBLY
Parts to be fastened to the unit should be located and accounted
for (See List and Figure 1).
IMPORTANT: Do not attempt assembly if parts are missing. Use
this manual to order replacement parts.
A
3
/
8
-16 x
3
/
4
” Hex head bolt, 2 each
B
3
/
8
” Flat washer, 4 each
C Tool rest bracket (left & right), 2 each
D Tool rest (left & right), 2 each
E
5
/
16
” Flat washer, 2 each
F
5
/
16
-18 x 1” Knob, 2 each
G #10-24 x
3
⁄
8
” Pan head screw, 4 each
H Upper eyeshield bracket (left & right), 2 each
I
Eyeshield, 2 each
J
Lower eyeshield bracket, 2 each
K
1
⁄
4
-20 x
1
⁄
2
” Knob, 2 each
L Spark guard (left & right), 2 each
M
3
/
8
-16 x
1
⁄
2
” Knob, 2 each
Dust collector hose not shown.
TOOL REST ASSEMBLY
•
Place tool rest (D) over tool rest bracket and secure in position
with
5
/
16
-18 x 1” knob (F).
•
Attach tool rest bracket to the bottom of the left wheel guard
using one
3
⁄
8
-16 x
3
⁄
4
” heax head bolt (A) and one
3
⁄
8
” flat wash-
er (B). Make sure that the slot of the braket is located over the
raised boss on the guard. Tight bolts finger tight.
•
Position tool rest so that distance between tool rest and grind-
ing wheel is less than
1
/
16
”. Reposition angle of tool rest if neces-
sary. Secure all knobs and bolts.
•
Mount right tool rest in a similar manner.
EYESHIELD ASSEMBLY
•
Attach spark guard (L) to left wheel guard using
3
⁄
8
-16 x
1
⁄
2
”
knob (M) and
3
/
8
” flat washer (B).
•
Mount left upper eyeshield bracket (H) to eyeshield (I) using
two #10-24 x
3
⁄
8
” pan head screws (G) ad lower eyeshield
bracket.
NOTE: Left upper eyeshield bracket is stamped “L” for identification.
•
Slide
1
/
4
-20 x
1
/
2
” knob (K) through hole at top of left spark guard
(L) into upper upper eyeshield bracket (H) and secure in
position.
•
Locate eyeshield in desired position for protecting operator
and secure all knobs and bolts.
•
Mount right eyeshield assembly in a similar manner.
DUST COLLECTOR HOSE
•
A dust collector hose has been provided with grinder. Slide
hoses onto sides of T-connector and flanges. Mount the hose
by sliding the flanges at each end over the exhaust ports on
the left and right wheel guards. Attach 2½” shop vacuum hose
to collector hose. Be sure hose is mounted securely.
DANGER:
Be sure to empty shop vacuum of all flammable materi-
al (flammable liquids and vapors, paper, wood, plastic, etc.) before
connecting vacuum to grinder. Hot sparks from grinder may ignite
flammable materials in shop vacuum.
Palmgren Operating Manual & Parts List
82061C, 82062C, 82071C, 82081C & 82101B
J
G
C
B
B
D
E
F
A
K
L
M
I
H
Figure 1 – Left Tool Rest and Eyeshield Assembly