•
Rotate spindle until inner slot is aligned with outer slot. You will
see through spindle when slots are properly aligned.
•
Insert the drift key (Ref. No. 51) into the slots and tap lightly
with hammer. The arbor and chuck will drop from spindle.
DIGITAL DISPLAY PANEL
Refer to Figure 6.
•
Display panel ‘A’ shows the depth of the spindle and spindle
RPM.
•
Button ‘B’ turns power on and off to Display ‘A’.
•
Button ‘C’: Press once for spindle depth in inches; press again
for spindle depth in mm; press once again for spindle RPM.
•
Button ‘D’ resets display at zero for spindle depth.
MAINTENANCE
WARNING:
Turn switch off and remove plug from power source
outlet before maintaining or lubricating your drill press
DRIVE BELT
Replace drive belt when worn.
LUBRICATION
Refer to Figures 7 and 8.
The ball bearings are lubricated at the factory and need no further
lubrication. Using 20wt. non detergent oil, periodically lubricate
the splines (grooves) in the spindle and the rack (teeth on the
quill) as follows:
•
Lower quill assembly (Figure 8, Ref. No. 29) all the way down.
•
Apply lubricant around the inside of the hole in the spindle
pulley (Figure 8, Ref. No. 2).
•
Apply lubricant to rack (teeth) on quill (Figure 8, Ref. No. 29)
while extended below drill press head.
•
Apply lubricant to rack and pinion gear (Figure 7, Ref. Nos. 8
and 18) on column and table assembly.
CLEAN MOTOR
Frequently blow out any dust that may accumulate inside motor. If
power cord is worn, cut or damaged in any way, have it replaced
immediately.
6
3605
2101
1699
1453
973
596
424
309
231
in/mm
5/16
7.9
5/8
15.9
3/4
19.0
7/8
22.2
1
25.4
1
1
⁄
4
31.8
1
5
⁄
8
41.3
1
3
⁄
4
44.4
2
50.8
in/mm
3/16
4.8
3/8
9.5
7/16
11.1
1/2
12.7
5/8
15.9
3/4
19.0
7/8
22.2
15/16
23.8
1
25.4
in/mm
11/64
4.4
11/32
8.7
13/32
10.3
15/32
11.9
1/2
12.7
11/16
17.5
3/4
19.0
13/16
20.6
—
—
in/mm
5/32
4.0
5/16
7.9
3/8
9.5
7/16
11.1
1/2
12.7
5/8
15.9
13/16
20.6
7/8
22.2
—
—
in/mm
7/64
2.8
1/4
6.4
5/16
7.9
11/32
8.7
3/8
9.5
1/2
12.7
5/8
15.9
3/4
19.0
—
—
in/mm
3/32
2.4
5/32
4.0
3/16
4.8
1/4
6.4
5/16
7.9
3/8
9.5
1/2
12.7
5/8
15.9
—
—
in/mm
1/16
1.6
1/8
3.2
1/8
3.2
3/16
4.8
1/4
6.4
5/16
7.9
7/16
11.1
1/2
12.7
9/16
14.3
in/mm
1/32
0.8
1/16
1.6
1/16
1.6
1/8
3.2
3/16
4.8
1/4
6.4
3/8
9.5
7/16
11.1
1/2
12.7
RPM
Wood
Zinc Diecast
Alum. & Brass
Plastic
Cast Iron &
Bronze
Steel - Mild &
Malleable
Steel - Cast &
Med. Carbon
Steel -
Stainless
& Tool
E
D
C
B
A
Z
Y
X
W
5
4
3
2
1
Motor
Spindle
120
161
231
281
309
424
540
567
596
622
973
1453
1699
2101
3083
3605
A1-5Z
A1-4Y
B2-5Z
A1-3X
B2-4Y
C3-5Z
B2-3X
C3-4Y
A1-2W
D4-5Z
E5-4Y
D4-3X
E5-3X
C3-2W
D4-2W
E5-2W
RPM
Belt
Location
Figure 5 – Spindle Speed Adjustment
Figure 6 – Digital Display Panel
ZERO
UNITS
A
B
C
D
0.000
mm
Palmgren Operating Manual & Parts List
80207
