GTV
FORCED CONVECTION AIR HEATERS
User’s Manual
6
ATTENTION
!
FORBIDDEN!
•
Never use the unit to support other equipment.
•
Never leave tools, spare parts, etc� inside the unit�
•
Make sure that all inspection panels are closed properly�
•
Do no expose the unit to inflammable gases.
ATTENTION
!
ONLY
QUALIFIED
PERSON
•
In case of breakdown or failure: turn unit off, do not try to repair it on your own, call operator.
•
If you are going to leave the heater switched off for a long time, first make sure that in no way this could cause
harm to anyone in any way�
•
The delivery must be made according to the following:
→
The package must be carefully secured in the loading space�
→
The package must be transferred in a closed space (always keep packing parts away environmental impacts)�
•
The unit has a special safety packing for transport and delivery which must be kept in good conditions till the unit is positioned
on the installation place�
•
Make sure that the unit has all its parts, as specified in the order.
•
Check if there are any damages and if the unit abbreviation is the same as the one of the ordered model�
•
Every unit is factory tested before shipment, therefore, if there are damages, report them immediately to the carrier�
Transporting, unloading and moving is a process which must be made carefully to avoid any kind of damages. Try not to use the unit’s
components as hand holds. When lifting, bear in mind that the centre of gravity of the unit may be off-centre.
CAUTION
!
DANGER
!
ATTENTION
!
THE USIGE OF
MOVING EQUIPMENT
IS COMPULSORY
ATTENTION
!
FORBIDDEN!
ATTENTION
!
ONLY
QUALIFIED
PERSON
The device is placed in cardboard box, one-way pallets are delivered�
Unpacking process:
• remove the bands from packing of device, the carton box and the covering foil. Screw off the 4 pcs M8x45 fixing bolts on back
side of pallet hereby the device can be removed from pallet�
•
do not remove the protection caps from device and gas installing set until the gas attachment
•
investigate the device if it is not damaged during the transportation
•
if it is damaged in that case notify the retailer from whom the device was bought!
There is an envelope inside the unit containing the Instructions for Installation and Servicing, User’s Guide use and Guarantee and ser
-
vices and the warranty documents�
The appliance operates based on direct heater principle, that means the heater air is blowed into the heated room directly for assuring of
requested temperature. Besides HEATING (winter) mode the appliance can achieves the VENTILATION of room as well (summer mode).
Principle:
The warm air blower appliance burns up the sucked mixture of combustion air and gas (S-,L-,Propan or natural gas), in this
way making the heater air,which is blowed into the heated room (by direct blowing or through air duct) in order to ensure the keeping of
temperature on requested value.
The heating and consumption values to be found as per appliance and gas types in the
enclosure 1.b.
The supply of combustion air of appliance can be realized in two ways:
•
directly from the heated place (A,C)
•
from open air (CL), it can be used in case of such plants, which are working with dangers materials as follows: painting work-
shops and workshops,which are using explosive or corrosive materials etc…
The combustion products flow through the exchanger pipes towards the flue system while heat up it, parallel with this process the blower
fan circulates the sucked inside or outside air through the heat exchanger assuring the needed warm air for heating� (the heater air is
average 50°C)
The air supply of blower fan can be solved in two ways:
•
by direct sucking in from the heated place (A, C, CL types),
•
by sacking in from outside (CL type)�
The made warm air can be passed into the heated place in two ways:
•
by direct blowing in through the leading lamellas (A, C types),
•
by blowing in and leading through air duct to the demanded places (in this case there are no lamellas on the device)�Such as
the C and CL type of GTV�
The technical data of appliance can be found in the
enclosure 1.
3.
Transportation, unpacking, handling
4.
Operation principle
