background image

150-204-111-01, Revision 01

 

Using This Technical Practice

HRE-204 List 1A and List 2A

April 7, 2000

 iii

U

SING

 T

HIS

 T

ECHNICAL

 P

RACTICE

The following conventions are used in this manual:

Monospace type

 indicates screen text, including text you type at a screen prompt.

Keys you press are indicated by small icons such as 

. Key combinations to be pressed simultaneously 

are indicated with a plus sign as follows: 

 + 

.

Three types of messages, identified by icons, appear in text.

For a list of abbreviations used in this document, refer to 

“Appendix C - Abbreviations” on page 22

.

D

OCUMENTATION

If you have comments on this PairGain document, send an email to [email protected]. Type 
the product name and the section number of the document in the subject area of the email message.

I

NSPECTING

 S

HIPMENT

Upon receipt of the equipment:

Unpack each container and inspect the contents for signs of damage. If the equipment has been damaged in 
transit, immediately report the extent of damage to the transportation company and to PairGain. Order 
replacement equipment, if necessary.

Check the packing list to ensure complete and accurate shipment of each listed item. If the shipment is short 
or irregular, contact PairGain as described in the Warranty located inside the back cover. If you must store 
the equipment for a prolonged period, store the equipment in its original container.

Notes contain information about special circumstances.

Cautions indicate the possibility of equipment damage or personal injury.

The Electrostatic Discharge (EDS) susceptibility symbol indicates that a device or assembly is 
susceptible to damage from electrostatic discharge.

ENTER

CTRL

ESC

Summary of Contents for HRE-204 List 1A































Reviews: