background image

                                                                      

FKM-GKM

 

 

 

©UAB V. Padagas ir ko. All right reserved.

  

16 

 
 

 

Periodically (at least once a month) 

 

After repair works. 

The  operator  must  ensure  that  the  hydraulic  hoses  are  replaced  after  a  certain  period  of  time, 

even if there are no visible defects. Hydraulic hoses should not be used for longer than 6 years. The 

date of manufacture and the permissible dynamic pressure are specified on the hose. 

5.4 OPERATING THE SWEEPING MACHINE 

After  checking  all  the  safety  equipment  and  hydraulic  connections,  you  may  start  using  the 

sweeping machine. 

The working speed of the sweeping machine depends on the type of surface being cleaned and 

the amount of rubbish (but must not exceed 10 km/h).

                                                                                                               

When operating the sweeping machine: 

 

If there are three supporting casters, it is necessary to monitor that the sweeping machine 

is running on the casters during operation. 

 

It is necessary to observe that the weight of the loader does not press the sweeping 

machine. 

 

Connect the hydraulic hoses so that the shaft rotates in the right direction. 

 

Make sure the casters and the garbage bin do not interfere with the shaft. 

 

The turned position of the sweeping machine may be selected only when working without 

the garbage bin. 

 

Before sweeping, check if the garbage bin is mounted properly and the shaft is pressed to 

the base. Pressing the shaft is carried out by raising or lowering support wheels. When the 

rings  are  worn  out,  the  support  wheel  must  be  lowered  so  that  the  sweeping  segments 

would touch the surface being cleaned. 

 

If the lower rubber of the bin is worn out, the bin must be tipped to press the rubber to the 

ground.  Bin  tipping  is  adjusted  by  shortening  the  tipping  rod  of  the  hydraulic  cylinder 

(Fig. 4). 

Note:

  When  assembling  a  new  shaft,  make  sure  the  axle  is  not  bent.  Repair  of  the  hydraulic 

system  may  be  carried  out  only  in  an  authorised  workshop.  The  safe  condition  of  the  sweeping 

machine must be monitored during its daily operation. 

Note:

 

If sweeper with the box  and side brush is monted in the tractors end,  the sweeper 

can not be torned to the sides

Summary of Contents for FKM-GKM 130


















Reviews: