background image

 

 

32 

 

The drip tray should be cleaned periodically according to the using situation. 

 
NOTE: Allow the drip tray to cool before attempting to clean.

 

 

OVEN RACKS 
 

The oven racks can be cleaned immediately after cooking is completed and after turning off 
the oven. Wear a barbecue mitt and scrub the oven racks with a damp cloth. If the oven is 
allowed to cool down, cleaning the grates will be easier if removed from the oven and cleaned 
with a mild detergent. 

 

STAINLESS STEEL 
 

After initial usage, areas of the oven may discolor from the intense heat given off by the 
burners. 
This is normal. Purchase a mild stainless steel cleaner and rub in the direction of the grain of 
the metal. Specks of grease can gather on the surface of the stainless steel and bake on to the 
surface and give a worn appearance. For removal, use a non-abrasive oven cleaner in 
conjunction with a stainless cleaner. 
 

NOTE: Always scrub in the direction of the grain. 

 

OVEN LIGHT 
 

Bulb Replacement 

IMPORTANT SAFETY INSTRUCTIONS 
Lighted lamp is HOT:

 

 

 

WARNING 

-TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO 

EXCESSIVE UV RADIATION, OR INJURY TO PERSONS

.

 

 

1. Turn off/unplug and allow to cool before replacing bulb (lamp). 

2. Bulb (lamp) gets HOT quickly! Only contact switch/plug when turning on. 

3. Do not touch hot lens, guard, or enclosure. 

4. Do not remain in light if skin feels warm. 

5. Do not look directly at lighted lamp. 

6. Keep lamp away from materials that may burn. 

7. Use only with a 10-watt or smaller bulb (lamp). 

8. Do not touch the bulb (lamp) at any time. Use a soft cloth. Oil from skin may damage bulb 
(lamp). 

9. Do not operate the portable luminaries with a missing or damaged guard, lamp containment 
barrier, or UV filter. 

Summary of Contents for PL8304SS
















































Reviews: