Pacific Living PL8304SS Owner'S Manual Download Page 1

Page: 1 / 47

Pacific Living

Outdoor Gas Oven

Owner’s Manual

(for the followings models: PL8430SSBG070,

PL8304SS, and PL8430SS)

WARNING

Improper installation, adjustment,

alteration, service or maintenance can

cause injury or property damage. Read

this instruction manual thoroughly

before installing or servicing this

equipment.

MODEL # PL8430SSBG070 with cart included

Model # PL8304SS & Model #PL8430SS

counter-top and built-in models

**Go to Page 14 for Oven Only Assembly Instructions**

WARNING

1. Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP tank not connected for use

should not be stored in the vicinity of

this or any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open the oven door.

4. If the odor continues, keep away from

the appliance and immediately call your

gas supplier or fire department.

WARNING

For Outdoor Use Only

Summary of Contents for PL8304SS
















































Search results

Summary of Contents for PL8304SS

Reviews:

Related manuals for PL8304SS

Brands by name

Popular brands

Pacific Living PL8304SS, Owner'S Manual

Search results

Summary of Contents for PL8304SS

Reviews:

Related manuals for PL8304SS

Brands by name

Popular brands