background image

071111-20 

SUPER-SD1 13

Troubleshooting

Problem  

Cause 

Cure

Glass is Dirty 

1. Wood is wet 

- Use dry wood

 

2. Turning down air control 

- Do not turn down until

 

  or damper too soon 

  a) there is a good bed of coals 

 

   

  b) the wood is charred

 

3. Draft too low 

- Improper chimney height and / or diameter 

 

   

- Chimney plugged or restricted, check fl ue 

 

   

- Provide outside air for combustion

 

4. Door gasket leakage 

- Replace gasket 

 

   

- Check latch

Excessive Creosote Buildup - See 1,2,3, above.

Low Heat Output 

1. Wood is wet 

- Use dry wood

 

2. Fire too small 

- Build a larger fi re

 

3. Draft too low 

- Chimney plugged or restricted, inspect and 

clean

Won't Burn Overnight 

1. Air control is set too high 

- Set control lower

 

2. Not enough wood 

- Unsplit wood is preferred for overnight burns

 

3. Draft too high 

- Excessive chimney height and/or diameter,

 

  

 see 

page 

11

Stove Won't Burn 

1. Combustion air supply blocked  - Check outside air supply for obstruction 

 

   

- Check that room air cover is removed

 

2. Draft too low 

- Chimney plugged or restricted, inspect and 

clean

Appendix A

Summary of Contents for SUPER 27 SPECTRUM





















Reviews: