background image

5055.5154-A

FP30 Arch Craftsman 240417-16

8

When the Craftsman Arched Front is installed on a FP 30 AR Series B Fireplace, the chase requires 

16sq.in. 

[100cm2]

 of chase inlet air. This air helps support the fireplace’s convection airflow and is separate from the 

Combustion Intake air. The duct doesn’t have to be round or a single inlet. The requirement is that the total 
inlet area must be equal to 16sq.in. or greater. 

This air must enter the chase no higher than 12” [305mm] from the bottom of the fireplace. And can be placed 
on the front (off to the side of the unit (Figure 6 on page 7) or on the sides or back of the chase if it pro-
trudes into the room. Air can be drawn from under the chace if that space is sealed within the house enve-
lope. The air must come from inside the house, preferably the room the fireplace is installed in.

Dimensions to note when installing the non-combustible wall board

A

Non-combustible wall board and all decorative facing materials.

B

Minimum height from base of the fireplace covered by non-combustible wall 
board

84” (2.135m)

C

Minimum width of non-combustible wall board covering front of unit.

60”(1.525m

D

Supplied steel stud wall section.

E

Combustible stud framing.

F

Chase air intake - locate on front between unit and chase side wall if the chase 
front is flush with wall. (see Figurue 5 for distance from opening).

Min. 16 sq.”  (100 cm2)

F

Chase air intake - Can be located on the side, back or underneath the chase, 
as long as that inlet is drawing air from inside the house.

Min. 16 sq.”  (100 cm2)

E

D

A

B

C

F

Figure 7:  FP30 Installed 3.

 CHASE INLET 

Summary of Contents for FP30 Arch Craftsman

















Reviews: