Paccar Peterbilt 320 Operator'S Manual Download

Page: 173 / 212

PART 8: MAINTENANCE AND SERVICE

Engine Cooling System

03019

Surge Tank

Proper Coolant Level

NOTE: Do not over

ll a cooling system. Excess

coolant may result in over

ow, loss of antifreeze,

and reduced corrosion protection.

• The proper coolant level for a cold engine is at the base

of the

ller neck extension tube.

• The proper coolant level for an engine at normal oper-

ating temperature is even with the pressure cap seal.

lling Your Radiator

1. Be sure the radiator and engine block drains are

closed.

2. Move the heater control to maximum heat position.
3. Remove the surge tank pressure cap
4. Through the surge tank,

ll the system with premixed

coolant. Pour it in a steady

ow until the radiator is full.

5. Start the engine.
6. Idle at low RPM.
7. Complete the

lling. Do it as quickly as possible.

8. Idle the engine until it reaches normal operating tem-

perature.

9. Fill the radiator as necessary to raise the coolant level

to the proper reading. Replace the surge tank pres-
sure cap.

Check the coolant level after each trip when the engine
has cooled. Add coolant as necessary. You may

your coolant level is not up to the correct level soon after
you have

lled the radiator. This may be because all the

trapped air in the system has not yet been purged. It takes
a little time for all the air to leave the system after you

your radiator.

R(08/07)

Y53-6015

– 169 –

Summary of Contents for Peterbilt 320





















































































































































































































Search results

Summary of Contents for Peterbilt 320

Reviews:

Related manuals for Peterbilt 320

Brands by name

Popular brands

Paccar Peterbilt 320, Operator'S Manual

Search results

Summary of Contents for Peterbilt 320

Reviews:

Related manuals for Peterbilt 320

Brands by name

Popular brands