Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
RPK4-HD1101
P
ifi A
C
ti
Page 10
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V8
Date: 081318
53.+'7HVWLQJDQG9HUL¿FDWLRQ
1.
Turn the ignition to the on position.
2.
Turn on the radio and check balance, fade and that all steering wheel controls are functioning properly.
3.
Verify that all of the HVAC controls are functioning properly.
4.
Verify that all of the steering wheel controls are functioning properly.
Technical Support and Product Updates (Firmware)
7KH5DGLR352DSSZLOODOVRDOORZ\RXWRXSGDWHWKHLQWHUIDFHZLWKQHZ¿UPZDUHDVLWEHFRPHVDYDLODEOH3OHDVHYLVLW
3$&DXGLRFRP)LUPZDUHRUFRQWDFWRXUWHFKVXSSRUWGHSDUWPHQWWRVHHLIWKHUHLVD¿UPZDUHXSGDWHIRU\RXULQWHUIDFH
Email:
Phone:
866-931-8021
International:
727-572-9255 ext 230
Troubleshooting
1.
Steering wheel controls work intermittently. This is typically caused by the original Honda “clock spring” aging. - Install
the included .47uF non polarized capacitor between the steering wheel control wire (White) and the steering wheel return
wire (Black). For more information on installing this capacitor, there is a tech brief located in the download section of the
RPK4-HD1101 product page on the PAC website (PAC-audio.com).
P8. - Upper Display Screen Type
This selection is only applicable when the vehicle is equipped with factory navigation. It allows the user to select if they have a Type 1 display (2003
- 2004) or a Type 2 display (2004 - 2007).
Note:
If the wrong type is selected the temp display on the upper screen will be garbled.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the A/C
and Dual (dual zone)
or Fan Speed (single zone)
button at the same time.
3.
While holding these buttons down, turn the key to the ignition position and continue to hold for 7 seconds or until “P8” is shown on the display.
4.
This tells you that you are in programming menu 8 along with the current selection on the right of the display which is 1 by default. The
available selections are as follows:
1. Type 1 (2003 - 2004)
2. Type 2 (2004 - 2007)
5.
Using the Fan Up
and Fan Down
buttons change the current selection to match the display type in the vehicle.
6.
Once the desired selection is shown, press the rear defrost button
(next to the
button) to select and exit.
RPK4-HD1101 Settings Menu (cont.)
P7. - Reset
This selection allows the user to reset the HVAC portion of the kit and return it to the initial HVAC type selection found at the bottom of page 6.
1.
Start with the Ignition in the OFF position.
2.
Press and hold the MAX A/C
and Auto
or Temp
button at the same time.
3.
While holding these buttons down, turn the key to the ignition position and continue to hold for 7 seconds or until “P7” is shown on the display.
4.
This tells you that you are in programming menu 7 along with the current selection on the right of the display which is 1 by default. The
available selections are as follows:
1. Exit (without resetting)
2. Reset
5.
Using the Fan Up
and Fan Down
buttons change the current selection to match the desired function.
6.
Once the desired selection is shown, press the rear defrost button
(next to the
button) to select and exit.
