PAC RP5-GM11 Manual Download Page 3

Pacific Accessory Corporation

Radio Replacement & Steering Wheel Control Interface 

with OnStar Retention for General Motors Vehicles

RP5-GM11

Rev. 092117

Page 3

© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

PAC-audio.com

Optional Steering Wheel Control Programming

Alpine

JVC

Kenwood

Clarion

Other

Pioneer

Sony

Fusion

1

2

Volume -

Volume -

Volume -

Volume -

Volume -

Volume -

Volume -

Volume -

3

Mute

Mute

Mute

Mute

Mute

Mute

Mute

Mute

4

Source

Source

Source

Source

5

Preset -

Track +

Play

Preset -

Preset -

Preset -

Track +

6

Source

Track -

Track +

Search -

Source

Source

Source

Track -

7

Track +

Band / Disc +

Track -

Band

Track +

Track +

Track +

Audio

8

Track -

Preset / Disc -

Disc / FM +

Send / End

Track -

Track -

Track -

Power

9

Power

Select

Disc / AM -

Send 

Band

Band

Band

10

Enter/Play

Attenuation

Answer

End

Answer

Phone Menu

Reject Call / Source 

(Bluetooth

equipped radios 

only)

11

Band / Program

Phone Receive

Voice Dial

VR

End

Answer Call

Answer / End Call

12

Receive

Phone Reject

On Hook

PTT

End Call

13

End

Voice Dial

Off Hook

VR

14

VR

Power

Mute  (Multimedia 

units only)

15

 - Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon

 - Jensen & Advent ONLY

Optional Programming Order

Programming

1.  Turn the key to the ignition position.

2.  Press and release programming button on the side of the interface.

3. 

Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed. 

4. 

If you need to program more buttons, repeat step 3  for each additional audio function on the steering wheel.

5. 

If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and 

release the program button on the side of the interface to skip that function. 

6. 

Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.

7.  Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function 

does not work, repeat the programming steps

If you wish to re-assign the SWC functions the interface must be programmed in the specific order shown on the chart below. If 

you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release 

the programming button on the side of the interface to skip that function. The LED will flash off and on confirming that you have 

successfully skipped that function and are ready to proceed to the next one.

Testing and Verification

1.  Turn  the ignition on. The LED on the interface will turn on and the +12v accessory wire will turn on.
2.  Turn on the radio and check balance and fade. Note: 

Premium Factory amplified Systems

 will not fade as neither the 

aftermarket radio or the RP interface have the ability to control the amplifier’s fader.

3. 

Verify that the factory subwoofer (if present) is playing

4.  Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the 

OnStar button on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8 

times before returning to the original level.

5.  Pressing the OnStar button on the rearview mirror will turn off the rear speakers and allow the OnStar audio to be heard in 

the two front speakers. The OnStar active LED will also turn on. When OnStar disconnects, the radio will un-mute or turn 

back on and the OnStar LED will turn off. Pressing the Mute/OnStar button on the steering wheel for 1.5 seconds will also 

activate Onstar.

6.  Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until the drivers door is opened.

Reviews: