background image

RP4-FD11

Radio Replacement & Steering Wheel Control Interface 

for Ford/Lincoln/Mercury Vehicles

Pacific Accessory Corporation

®

 | Santa Ana, California 92705 | Ph. 866-931-8021 | [email protected] 

©2011 Pacific Accessory Corporation

www.pac-audio.com

Rev. 112811

Pacific Accessory Corporation

Rear Seat Entertainment (RSE); If equipped

If you would like for the RSE system’s audio to 

play through the aftermarket radio:

 

First set the aftermarket radio to Aux input.

 

Press 

the Power button on the RSE & insert a DVD. You 

should now hear the RSE audio on the aftermarket 

radio. If the RSE audio is only playing on the front 

speakers the RSE is set to dual zone mode. Press 

the Dual Zone button on the RSE controls until 

“Single Play” is displayed across the top of the RSE 

screen.

RSE Audio Modes - 

There are 2 different modes for 

the RSE audio, they are Single Play & Dual Play.

1. Single Play - 

Press the Dual Zone button on the 

RSE controls until “Single Play” is displayed across the 

top of the RSE screen. In this mode the RSE audio is 

played throughout all speakers in the cabin.

2. Dual Play - 

Press the Dual Zone button on the RSE 

controls until “Dual Play” is displayed across the top 

of the RSE screen. In this mode the rear speakers will 

be muted & the RSE audio is transmitted through the 

factory IR headphones while the front passengers can 

now listen to whatever source they like.

RSE Operation Notes:

1. If the vehicle is equipped with RSE with single play/

dual play button on the monitor in the headrests, the 

driver side monitor is the master source unit. The 

source on 

     the passenger headrest cannot be viewed on the 

driver side.

2. Both monitors must turn headphones off in order to 

hear rse audio through radio.

3.  Monitors  without  single  play/dual  play  button  on 

monitor operate independantly and audio can never 

be  passed  to  the  new  radio.  In  these  vehiicles  rse 

audio comes from aux in on back of center console.

4. In 2011+ vehicles the car must be in ignition mode 

for the RSE to operate properly. Being in acc mode will 

cause erratic behavior.

ENTER

MENU

RETURN

VOLUME

MEDIA

Vehicles With Overhead Monitor

Dual Play

Button

MEDIA

MENU

SEL

Vehicles With Headrest Monitor

Dual Play

Button

Product Updates (Firmware)

The RP4-FD11 can be updated with new firmware as it becomes available using the PAC-UP interface updater (sold seperatly). 

Please visit www.pac-audio.com/firmware for available updates.

Page 5

Page 4

Summary of Contents for RadioPRO4






Reviews: