Ozotech AIM BTU 1000 Quick Start Manual Download Page 4

5) Inlet and Outlet Hose Connections

The AIM Series Ozone Generator is designed to feed ozone to a variety of applications with a minimum 

flow rate of 3 SCFH and a maximum of 20 SCFH. Lower pressures and flow rates generally achieve best 

performance. A variety of hose connectors and adapters are provided in the hose adapter kit to step-up 

or down hose sizes, to fit your application. The AIM Series Ozone Generator may be used in both positive 

and negative pressure applications. The use of snapper clamps on all positive pressure application 

connections is recommended.

Positive pressure feed applications— It is recommended that pure oxygen from a tank or 

concentrated oxygen from an oxygen concentrator machine be used to supply the feed gas for optimum 

performance, but clean dry air can also be used. Compressed air or gas must be pressure regulated 

to 5 psi or less. Lower pressures and flow rates generally achieve best performance. Connect the feed 

gas supply to the inlet hose (closest to the access door) and connect ozone feed line to the outlet 

hose (closest to back of chassis). Turn on gas flow and fine tune the flow rate to suit your application 

by adjusting the flow meter knob on the front door of the AIM Series Ozone Generator. Temporarily 

installing an inline or T-branch manometer, or other fine resolution pressure sensing instrument, on the 

outlet hose is a good way to verify internal pressures are not too high. A check valve in the ozone outlet 

line must be installed between the ozone generator and delivery device.

Negative pressure applications—This machine can be used with vacuum draw systems as well, 

provided the minimum air flow rate (3 SCFH) and internal chamber pressures (≤5 psi) requirements are 

met. Like positive pressure applications, it is recommended that bottled or concentrated oxygen feed 

gas be used to supply the ozone generator. Connect the inlet and outlet tubing in the same fashion as 

described above. Install the supplied BF1 - Backflow Prevention Device between the ozone generator 
and inline check valve on the ozone output line.

Summary of Contents for AIM BTU 1000

Page 1: ...Care Guide 1 31011 BF1 Back Flow Prevention Device 60 44244 1 Ozone Resistant 1 4 ID tubing 24 44141 1 Ozone Resistant 3 8 ID tubing 1 33258 01 Accessory Hose Adapter Kit as follows 4 44144 2 Snapper Clamp use with 3 8 OD hose 4 44134 4 Snapper Clamp use with 7 16 OD hose 4 44096 7 Snapper Clamp use with 1 2 OD hose 6 44071 10 Snapper Clamp use with 9 16 OD hose 2 44112 14 Snapper Clamp use with 5...

Page 2: ... the back panel as needed for custom installations See drawing at right for factory mounting hole spacing Handy Tip To better facilitate top lid removal space the unit out from the wall slightly about 1 8 and be sure to leave adequate clearance at the top to access and remove glass tubes 3 Electrical Connections The latest model of the AIM Series Ozone Generators are designed to accept either 115V...

Page 3: ...ted to remove caps let them hang gently to the side Step 3 a Place tube holder spring tension retainer item 44347 1 into the bottom of each chamber Inspect placement to ensure spring retainer is not sideways or upside down Step 4 a Carefully insert a glass corona tube item 40155 into each chamber Ensure the brass electrode end is up towards cap end Step 5 a Reinstall caps onto manifold s making su...

Page 4: ...ance Connect the feed gas supply to the inlet hose closest to the access door and connect ozone feed line to the outlet hose closest to back of chassis Turn on gas flow and fine tune the flow rate to suit your application by adjusting the flow meter knob on the front door of the AIM Series Ozone Generator Temporarily installing an inline or T branch manometer or other fine resolution pressure sens...

Reviews: