![background image](http://html1.mh-extra.com/html/ozito/zlcg-112u/zlcg-112u_instruction-manual_1666165001.webp)
1
CHARGER SAFETY WARNINGS
ELECTRICAL SAFETY
DESCRIPTION OF SYMBOLS
ZLCG-112U
FAST CHARGER
12V Lithium Ion
INSTRUCTION MANUAL
SPECIFICATIONS
Input:
100-240V AC 50-60Hz
Output:
15V DC, 1700mA
Charge Times:
1hr (1.5Ah Battery)
ozito-diy.co.uk
1
2
3
1 Charging Adaptor
2 Charging Cradle
3 Charge Indication Lights
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR
YOUR BATTERY CHARGER.
1.
Before using the charger read all instructions and cautionary markings on the charger,
battery pack and the product using the battery pack.
2.
This charger is not intended for any uses other than charging rechargeable batteries. Any
other use may result in risk of fi re, electric shock or electrocution.
3.
Do not place any object on top of the charger or place the charger on a soft surface that
may result in excessive internal heat. Place the charger in a position away from any heat
source.
4.
To reduce risk of damage to the electric plug and cord, pull by the plug rather than the
cord when disconnecting the charger.
5.
Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
6.
An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in the risk of fi re, electric shock or electrocution.
7.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise
damaged in any way. Have it checked by an electrician or power tool repairer.
8.
Do not disassemble charger. Take it to an electrician or power tool repairer when
service or repair is required. Incorrect reassembly may result in a risk of electric shock,
electrocution or fi re.
9.
To reduce risk of electric shock, unplug the charger from the outlet before attempting any
cleaning. Removing the battery pack will not reduce this risk.
10. Never attempt to connect 2 chargers together.
11.
DO NOT store or use the tool and battery pack in locations where the temperature may reach
or exceed 40ºC (such as inside sheds or metal buildings in summer).
12. The charger is designed to operate on standard household electrical power (240 volts).
Do not attempt to use it on any other voltage!
13. The battery pack is not fully charged out of the carton. First read the safety instructions
and then follow the charging notes and procedures.
14. The longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an air
temperature below 10ºC or above 40ºC. This is important and will prevent damage to the
battery pack.
15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out.
The battery can explode in a fi re.
16.
Never attempt to open the battery pack for any reason. If the plastic housing of the battery
pack breaks or cracks, immediately discontinue use and do not recharge.
17. During charging, the battery must be placed in a well ventilated area.
WARNING!
When using mains-powered tools, basic safety precautions,
including the following, should always be followed to reduce risk of fi re, electric
shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool. Save these instructions and other documents supplied
with this tool for future reference.
The charger has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for the UK.
This tools charger is double insulated; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in
order to avoid a hazard.
Note:
Double insulation does not take the place of normal safety precautions when operating
this tool. The insulation system is for added protection against injury resulting from a possible
electrical insulation failure within the tool.
The power supply for this products charger should be protected by a residual current device
(rated at 30mA or less). A residual current device reduces the risk of electric shock.
Warning
Read instruction manual
mA
Milliamperes
Polarity
Thermal cut-out protection
Double insulated
A
Amps
Indoor use only
V
Volts
Hz
Hertz
ac/~
Alternating current
W
Watts
Direct current
dc/
Ah
Amp hour
Manual_ZLCG-112U.indd 1
22.08.2019 15:35:39