background image

FWD

3.  KEYLESS CHUCK

4.  CONTROLS

OPERATION

Speed Control

1.   Slide the switch backward 

to select first gear.

2.   Slide the switch forward to 

select second gear.

The gear selector controls the speed of the drill. First gear allows 

slower drilling with more torque, while second gear is suitable when 

less torque but higher speed is required.

Forward/ Reverse Lever

Variable Speed Trigger

1   For forward rotation, push the fwd/rev lever towards the left side of 

the drill. For reverse rotation push fwd/rev lever to the right. The LED 

at the rear of the drill will also indicate direction.

1   To start drilling squeeze the 

variable speed trigger.

2   To stop drilling release the 

trigger.

Note:  

The more the variable speed trigger is depressed, the faster the 

drill bit will rotate.

Adjusting Torque

1   Rotate the torque collar to the desired setting.

Note:  

Selecting a higher torque setting will allow the drill to use more 

torque to drive the screw in or out. To prevent damaging the 

screw head, it is recommended to start at a low torque setting 

and increase when necessary.

Installing a Drill Bit

Removing a Drill Bit

1   Open the chuck by 

rotating the chuck collar 

and remove the frill bit.

2   Insert the drill 

bit, making sure 

it is centred in 

the chuck.

4   Pull on the bit 

to ensure it is 

firmly secured.

CAUTION: 

TO REDUCE THE RISK OF INJURY WE 

RECOMMEND THE USE OF GLOVES WHEN HANDLING 

DRILL BITS.

1   Rotate the chuck collar 

anti-clockwise to open the 

chuck 

3   Tighten the chuck by 

turning clockwise.

WARNING!

 

Ensure the tool is turned off & disconnected 

from the power supply before performing any of the following 

operations.

Summary of Contents for PXDDS-200











Reviews: