background image

GB

- 15 -

For example, you could use 2 x 4.0Ah batteries in 

one battery bank while using 2 x 3.0Ah batteries 

in the opposite battery bank.

Important!

Use only batteries which are charged to the same 

level. Never combine full and half-full batteries. Al-

ways charge the two/all batteries simultaneously.

The equipment‘s operating time depends on the 

battery with the lower charge level. The two/all 

batteries must always be fully charged before use. 

Close the battery cover by swinging it down, and 

make sure that it latches in place correctly.

Battery capacity indicator (Fig. 13)

Press the switch for the battery capacity indicator 

(Fig. 13/Item A). The battery capacity indicator 

(Fig. 13/Item B) shows the charge status of the 

battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack!

Caution!

Do not park the lawn mower in the sun. Batteries 

which have been inserted could heat up to inad-

missible levels.

6. Operation

Caution!

The lawn mower is equipped with a safety switch 

to prevent unauthorized use. Directly before star-

ting up the lawn mover insert the safety plug (Fig. 

10) and remove the safety plug again when inter-

rupting or terminating your work.

Important!

For safety reasons, it is not possible to start the 

cordless lawn mower if the pitch angle is over 

~60°.

Caution!

To prevent the equipment switching on acciden-

tally, the lawn mower is equipped with a safety 

switch (Fig. 10/Item 8) which must be pressed 

before the switching bar (Fig. 9/Item 1) can be 

activated. The lawn mower switches itself o

  when 

the switching bar is released. The start time can 

amount to several seconds (To make it easier to 

start, tilt the lawn mower slightly at the back (Fig. 

18)). The speed will drop after a few seconds 

when in idle mode and will rise again after a few 

second when in working mode. Repeat this pro-

cess several times so that you are sure that the 

machine functions properly. Before you perform 

any repair or maintenance work on the equipment, 

ensure that the blade is not rotating, that the safe-

ty plug (12) is disconnected and that the batteries 

(16) have been removed.

Warning! Never open the chute 

fl

 ap when the 

grass bag has been detached (to be emptied) and 

the engine is still running. A rotating blade can 

cause serious injuries!

Always carefully fasten the chute 

fl

 ap and grass 

basket. Before you remove them, switch o

  the 

motor and pull out the safety plug (12) 

fi

 rst.

Always ensure that a safe distance (provided 

by the length of the long handles) is maintained 

between the user and the mower housing. Be 

especially careful when mowing and changing 

direction on slopes and inclines. Maintain a solid 

footing and wear sturdy, non-slip footwear and 

long trousers.

Always mow along the incline (not up and down). 

For safety reasons, the lawn mower may not be 

used to mow inclines whose gradient exceeds 15 

degrees.

Use special caution when backing up and pulling 

the lawn mower. Tripping hazard!

Tips for proper mowing

It is recommended that you overlap the mo-

wing swaths.

Only use a sharp blade that is in good condition. 

This will prevent the grass blades from fraying and 

the lawn from turning yellow.

Try to mow in straight lines for a nice, clean look. 

The swaths should overlap each other by a few 

centimeters in order to avoid stripes.

How frequently you should mow your lawn is 

determined primarily by the speed at which the 

grass grows. In the main growing season (May 

Anl_PXCSDMK_418U_SPK7.indb   15

Anl_PXCSDMK_418U_SPK7.indb   15

22.08.2019   16:29:46

22.08.2019   16:29:46

Summary of Contents for PXCSDMK-418U





























Reviews: