background image

3. INSERTING & REMOvING ThE BATTERY

4.  CONTROLS & OPERATION

OPERATION

1.   Align the ribs of the battery with 

the recess in below the handle.

1.   Press and hold the battery 

release tab to release the 

battery.

2.   Slide the battery in so 

that it clicks into place.

1.   To start the blower 

squeeze the on/off 

switch.

2.   To stop the blower 

release the on/off 

switch.

2.   Slide the battery out.

Inserting the Battery into the Blower

Removing the Battery from the Blower

Switching On and Off

Blowing

The blower is ideal for blowing 

leaves, grass clippings and 

other debris. 

Hold the blower firmly, squeeze 

the on/off switch, point the jet 

of air in front of you and move 

forward slowly. Move the 

blower from side to side, with 

the tube several inches above 

the ground.

Be careful where you point the 

jet of air as it can move heavy 

material and cause injury or 

damage to bystanders.

Note:

 Be aware of other people and animals in the area where you are to 

be operating the blower.

Note:

 

Avoid collisions with hard objects which could damage your machine.

WARNING!: 

DO NOT USE ThE BLOWER WITh ANY 

TYPE OF ACCESSORY OR ATTAChMENT. SUCh 
USAGE MIGhT BE hAZARDOUS.

WARNING!: 

DO NOT PUT PART OF YOUR BODY 

SUCh AS hANDS AND FINGERS IN ThE vACUUM 
OPENING OR EXhAUST OPENING.

WARNING!: 

DO NOT SWITCh ThE BLOWER ON 

IN ENCLOSED OR POORLY vENTILATED SPACES 
OR IN ThE PRESENCE OF FLAMMABLE AND/OR 
EXPLOSIvE LIQUIDS, GASES AND POWDERS.

WARNING!

 DO NOT USE ANY ATTAChMENTS 

OR ACCESSORIES NOT RECOMMENDED BY ThE 

MANUFACTURER OF ThIS PRODUCT, AS IT CAN 

RESULT IN SERIOUS PERSONAL INjURY.

PXCBLK-418

Summary of Contents for POWER X CHANGE PXCBLK-418







Reviews: