MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
V
Hz
~
W
/min
n
o
Volts
Alternating current
Revolutions or
reciprocation per minute
Double insulated
Warning
Hertz
Watts
No load speed
Regulator compliance mark
• Keep the ventilation vents of the sander clean at all times, if possible, prevent
foreign matter from entering the vents.
• After each use, blow air through the sander housing to ensure it is free from
all dust particles which may build up. Build up of dust particles may cause the
sander to overheat and fail.
• If the enclosure of the sander requires cleaning, do not use solvents but a
moist soft cloth only. Never let any liquid get inside the sander; never immerse
any part of the sander into a liquid.
Carbon Brushes
When the carbon brushes wear out, the sander will spark and/or stop.
Discontinue use as soon as this happens. They should be replaced prior to
recommencing use of the sander. Carbon brushes are a wearing component of
the sander therefore not covered under warranty. Continuing to use the sander
when carbon brushes need to be replaced may cause permanent damage to
the sander. Carbon brushes will wear out after many uses but when the carbon
brushes need to be replaced, take the sander to an
electrician or a power tool repairer for a quick and
low cost replacement. Always replace both carbon
brushes at the same time.
Note: Ozito Industries will not be responsible for any
damage or injuries caused by the repair of the sander
by an unauthorised person or by mishandling of the
sander.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Excessive sparking visible through the housing air vents
and/or the sander failing to operate
May indicate the carbon brushes have worn out and need to be
replaced. Carbon brushes should only be replaced by a qualified
electrician or power tool repairer.
Sandpaper Selection
Selecting the correct grit of sandpaper is an important step in achieving
optimum results. Coarse grit will remove the most material. Finer grit will
produce a smoother finish. The condition of the workpiece will determine the
grit of the sandpaper to be used. The higher the grit number, the finer the
grade of sandpaper.
If the surface is rough, start with a coarse grit and sand until the surface is
uniform. Medium grit may then be used to remove scratches left by the coarser
grit. Finer grit is then used to finish the surface. Always continue sanding with
each grade of sandpaper until the surface is uniform.
MATERIAL
APPROPRIATE GRIT
Coarse Sanding
Fine Sanding
Paintwork
180
400
Wood
: Softwood
60
240
Hardwood
60
180
Veneer
240
320
Note
: If intermediate sanding is required, choose a grit rating between coarse and
fine. The above table is intended as a guide only. To ensure a satisfactory result,
a small, inconspicuous area should first be tested to ensure the grit of sandpaper
chosen is suitable for the desired finish.
On/off Switch
SPHSS5000-05
Carbon Brush (pair)
SPHSS5000-10
Metal Paper Clip
SPHSS5000-22
Holder
SPHSS5000-23
Foam Pad
SPHSS5000-31
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
Read instruction manual