background image

DESCRIPTION OF SYMBOLS

Care of the Battery

• Ensure that your battery is always fitted securely.

•  A perfect connection to the cable network of the electrical 

system must be ensured at all times.

•  Keep the battery clean and dry. Apply a thin coating of grease 

to the connection terminals using an acid-free, acid-resistant 
grease (Vaseline).

•  Check the level of the acid in batteries that are not maintenance-

free versions approximately every 4 weeks and top up with 
distilled water if necessary

 

Cleaning

  We recommend that you clean the device immediately each time 

you have finished using it.

  Clean the appliance regularly with a damp cloth and some soft 

soap. Do not use cleaning agents or solvents; these may be 

aggressive to the plastic parts in the appliance. Ensure that no 

water can get into the interior of the appliance.

Storage

  The battery charger should be placed in a dry room for storage. 

Any corrosion must be cleaned off the charging terminals.

Supply Cords

If replacement of the supply cord is necessary, this has to be done 

by a certified electrician in order to avoid a safety hazard.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person 

or by mishandling of the tool.

WARNING! 

BEFORE CLEANING THE APPLIANCE MAKE  

SURE THAT IT IS DISCONNECTED FROM THE MAINS 

POWER SUPPLY.

3.15 A

Regulatory Compliance Mark

(RCM)

Warning

V

Volts

A

Amperes

Read Instruction Manual

Double Insulated

Hz

W

Hertz

~

Alternating Current

Watts

mAh

Milliampere Hours

IP65

Ingress protection from dust & water

Ah

Amp Hour

Fuse value on PCB

Chassis or Frame Ground

Indoor Use Only

Power tools that are no longer usable should not 

be disposed of with household waste but in an 

environmentally friendly way. Please recycle where 

facilities exist. Check with your local council authority for 

recycling advice.

Recycling packaging reduces the need for landfill and 

raw materials. Reuse of recycled material decreases 

pollution in the environment. Please recycle packaging 

where facilities exist. Check with your local council 

authority for recycling advice.

CARING FOR THE ENVIRONMENT

MAINTENANCE

Summary of Contents for OCBC-600









Reviews: