background image

!

!

INTRODUCTION

3

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING
INSTRUCTIONS FOR YOUR BATTERY CHARGER.

Before using the charger, read all instructions and cautionary markings on
charger, battery pack and product using the battery pack.

Danger!

If the battery pack case is cracked or damaged, do not insert

into charger. There is a danger of electric shock or electrocution.

Warning!

Don’t allow any liquid to get inside charger. Electric shock may

result. To facilitate cooling of the battery pack after use, avoid placing the
charger or battery pack in a warm environment such as in a metal shed,
or an uninsulated trailer.

This charger is not intended for any uses other than charging rechargeable
batteries. Any other use may result in risk of fire, electric shock or electrocution.

Do not place any object on top of the charger or place the charger on a soft
surface that may result in excessive internal heat. Place the charger in a
position away from any heat source.

To reduce risk of damage to the electric plug and cord, pull by the plug rather
than the cord when disconnecting the charger.

Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.

An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord could result in the risk of fire, electric shock or electrocution.

Do not operate charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Have it checked by an electrician or power 
tool repairer.

Do not disassemble charger. Take it to an electrician or power tool repairer
when service or repair is required. Incorrect reassembling may result in a risk of
electric shock, electrocution or fire.

To reduce risk of electric shock, unplug charger from the outlet before
attempting any cleaning. Removing the battery pack will not reduce this risk.

Congratulations on purchasing an Ozito Lithium Ion Cordless
Drill . We aim to provide quality tools at an affordable price.

We hope you will enjoy using this tool for many years. Your
Lithium Ion Cordless Drill LIR-144 has been designed for
general purpose drilling or screwdriving around the home
and is intended for DIY use only.

ELECTRICAL SAFETY

!

Summary of Contents for LIR-144

















Reviews: