Installing or replacing an engraver tip
WARNING!
Disconnect the engraver from the power supply before making
any adjustments or undertaking maintenance procedures.
Make sure that the machine is switched off and the plug removed from the
mains outlet.
1. To replace the engraving bit (1),
unscrew in an anti-clockwise direction
and remove the locking nut (2), pull
the engraving bit (1) and spring out
of the engraver.
2. When replacing the engraving bit (1),
make sure that the spring has been
refitted on to the new Engraving Bit.
3. Re-fit the engraving bit (1) with spring
into the engraver.
4. Re-fit the locking nut (2) by screwing it onto the engraver in a
clockwise direction.
WARNING!
Always wear safety glasses when using this tool.
The Ozito electric engraver can be used to permanently mark metal, glass,
plastic, wood, ceramics and much more.
1. Before using the engraver you must
ensure there is an engraving tip (1)
installed (Refer to assembly section).
2. Connect the engraver plug to the
power supply and whilst holding the
engraver firmly, push and hold the
on/off switch (3) with your thumb.
NOTE:
To turn the tool on, press the
small on/off button (3).To turn the tool
off, release the on/off button (3).
3. Hold the engraver at an angle, like
you would holding a pen. Do not
press down hard while engraving,
use light pressure while guiding the
point over the workpiece.
Adjusting the engraving depth
1. The stroke adjustment dial (4) located on the top of the engraver controls
the stroke length and therefore the engraving depth.
2. For a fine mark turn the stroke adjustment dial (4) anti-clockwise.
3. For a deeper, thicker mark turn the stroke adjustment dial (4) clockwise.
WARNING!
Do not turn the dial more then 2 rotations.
NOTE:
It is recommended that you practice on scrap material before
you start.
WARNING!
Always ensure that the tool is switched off and the plug is
removed from the power point before making any adjustments or
maintenance procedures.
1. Use a soft brush to remove any accumulated dust. Wear safety glasses to
protect your eyes whilst cleaning.
2. If the body of the tool needs cleaning, wipe it with a soft damp cloth.
A mild detergent can be used but never alcohol, petrol or other harsh
cleaning agents.
3. Never use caustic agents to clean plastic parts.
CAUTION:
Water must never come into contact with the tool.
General inspection
Regularly check that all the fixing screws are tight. They may vibrate loose
over time.
Power cord maintenance
If the supply cord needs replacing, the task must be carried out by a
qualified electrician or power tool repairer in order to avoid a safety hazard.
Please refer to your warranty card, which is separate to these instructions.
Note:
Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the tool by an unauthorised person or by
mishandling of the tool.
Assembly
To View the full range visit: www.ozito.com.au
Maintenance
Caring For The Environment
Power tools that are no longer usable should not be
disposed of with household waste but in an
environmentally friendly way. Please recycle where
facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and
raw materials. Reuse of recycled material decreases
pollution in the environment. Please recycle packaging
where facilities exist. Check with your local council
authority for recycling advice.
Description of Symbols
Contents
1 x Engraver EER-012
1 x Instruction manual
1 x Additional engraving tip
OZITO INDUSTRIES PTY LTD
AUSTRALIA (Head Office)
1-23 Letcon Drive, Bangholme, Victoria,
Australia 3175
Telephone: 1800 069 486
Facsimile: + 61 3 9238 5588
Website: www.ozito.com.au
V
~
Hz
W
n
o
/min
S2: 8 min
Volts
Alternating current
Herts
Watts
No load speed
Revolutions or reciprocation per minute
Double insulated
Operation
Conforms to relevant standards for
electromagnetic compatibility
Indicates operating time at no more than 10 minutes
at rated load followed by a complete cool down of
the tool
Summary of Contents for EER-012
Page 4: ......
