background image

MAINTENANCE

DESCRIPTION OF SYMBOLS

TROUBLESHOOTING

•  Keep the ventilation vents of the angle grinder clean at all times, if possible, 

prevent foreign matter from entering the vents.

•  After each use, blow air through the angle grinder housing to ensure it is 

free from all dust particles which may build up. Build up of dust particles may 

cause the angle grinder to overheat and fail.

•  If the enclosure of the angle grinder requires cleaning, do not use solvents but 

a moist soft cloth only. Never let any liquid get inside the angle grinder; never 

immerse any part of the angle grinder into a liquid.

Carbon Brushes

When the carbon brushes wear out, the angle grinder will spark and/or stop. 

Discontinue use as soon as this happens. They should be replaced prior 

to recommencing use of the angle grinder. Carbon brushes are a wearing 

component of the angle grinder therefore not covered 

under warranty. Continuing to use the angle grinder 

when carbon brushes need to be replaced may 

cause permanent damage. Carbon brushes will wear 

out after many uses but when the carbon brushes 

need to be replaced, take the angle grinder to an 

electrician or a power tool repairer for a quick and 

low cost replacement. Always replace both carbon 

brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries caused 

by the repair of the 

angle grinder

 by an unauthorised person or by mishandling 

of the angle grinder.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents.  

This is normal and does not indicate a problem.

Excessive sparking visible through the housing air vents 

and/or the angle grinder failing to operate

May indicate the carbon brushes have worn out and need to be 

replaced. Carbon brushes should only be replaced by a qualified 

electrician or power tool repairer.

SPARE PARTS

  

V

 

    Volts 

 

 

            

Hz

      Hertz

  

~

 

    Alternating current 

            

W

 

    Watts 

 

              

 

 /min

      Revolutions or   

 

  

               reciprocation per minute

Double insulated 

Read instruction manual

Always wear gloves

Wear eye protection

Always wear ear, eye and

safety mask

n

o

       No load speed

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit 
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: [email protected]

Summary of Contents for AGS-4050U









Reviews: