ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1 Depress and hold spindle
lock button.
Da
ng
er: D
o not
exceed the max. safe
sp
ee
d
12
5m
m
(5”
) Metal Cuttin
g D
isc
M
ax
1
2,0
00
R
P
M
Da
ng
er: D
o not
exceed the max. safe
sp
ee
d
12
5m
m
(5”
) Metal Grindi
ng
D
is
c
M
ax
1
2,2
00
R
P
M
5 Screw the outer flange onto the spindle.
Note:
The flat surface on the flange should be in contact with
the cutting disc.
1 Spindle Lock Button
2 Grinding Guard
3 Side Handle
4 Safety Lock Off Switch
5 On/Off Trigger
ANGLE GRINDER
KNOW YOUR PRODUCT
AGB-1200
1. SIDE HANDLE & SAFETY GUARD
2. GRINDING DISC FITMENT
4. ON/OFF SWITCH
5. GRINDING & CUTTING
1 Ensure the workpiece is
securely held down.
2 Turn on the
angle grinder.
2 Rotate spindle to locate
the lock position.
A
B
10-15°
6 Cutting Guard
7 Pin Wrench
8 Grinding Guard
9 Inner Flange
10 Outer Flange
11 Metal Grinding Disc x 1
12 Metal Cutting Disc x 1
13 Diamond Cutting Disc x1
14 Spare Brushes
ACCESSORIES
SETUP & PREPARATION
OPERATION
The tool is recommended for use with a residual current device
with a rated residual current of 30mA or less.
Adjustable Safety Guards
A guard should be used at all times whilst operating the angle
grinder.
Inspect the grinding disc before fitment to ensure it is not cracked
or deformed. The grinding disc is suitable for grinding tasks only.
Only use grinding discs with a diameter of 125mm.
3 Begin grinding your workpiece. The optimum grinding
angle is 10-15
°
to the workpiece. Do not apply excessive
pressure. Allow the tool to do the work. This will prevent
deep gouging.
1 To turn the grinder on, first push safety lock off switch
forward (a), then depress trigger switch (b). Hold the
trigger switch in this position for continuous use.
2 To turn the grinder off, release the trigger switch.
3. CUTTING DISC FITMENT
Inspect the cutting disc before fitment to ensure it is not cracked or
deformed. The cutting disc is suitable for cutting tasks only. Only
use cutting discs with a diameter of 125mm.
4 Begin cutting your
workpiece. The optimum
cutting angle is 90
°
to the
workpiece. Do not apply
excessive pressure. Allow
the tool to do the work.
Grinding
Cutting
Use ONLY the Grinding
Guard with a grinding
disc.
Use ONLY the
Cutting Guard with
a cutting disc.
Removing
2 Remove the handle.
Side Handle
The side handle can be fitted on either side, or on top of your
grinder. The correct position will be determined by your preferred
hand and the operation being performed.
Attaching
1 Firmly attach the handle in the
desired position on the grinder.
Attaching
Removing
3 Loosen guard lever.
7 Use the above operation in reverse to remove grinding disc.
6 Depress and hold spindle
lock button. Firmly tighten
the outer flange with the
pin spanner.
Dan
ger
: D
o n
ot
exc
eed
th
e m
ax.
sa
fe s
pee
d
12
5m
m (
5”)
Max
12,0
00 RPM
3 Use pin spanner to
loosen and remove the
outer flange.
4 Insert the disc with the
label facing up.
5 Screw the outer flange onto the spindle.
Note:
The flat surface on the flange should be in contact with
the grinding disc.
CAUTION:
REGULARLY CHECK THAT THE OUTER
FLANGE HAS NOT BECOME LOOSE DURING
OPERATION.
CAUTION:
REGULARLY CHECK THAT THE OUTER
FLANGE HAS NOT BECOME LOOSE DURING
OPERATION.
1 Loosen guard lever, align
tabs and rotate guard to the
required position.
2 Tighten guard by pressing
the lever down.
4 Align tabs on the guard with
slots on the guard collar.
Remove guard.
1 Depress and hold
spindle lock button.
2 Rotate spindle to locate
the lock position.
7 Use the above operation in reverse to remove grinding disc.
6 Depress and hold spindle
lock button. Firmly tighten
the outer flange with the
pin spanner.
3 Use pin spanner to
loosen and remove the
outer flange.
4 Insert the disc with the
label facing up.
Use ONLY the
Grinding Guard
with a grinding
disc.
Use ONLY the
Cutting Guard with
a cutting disc.
125x1.9x22.23mm
A
B
Dan
ger
: D
o n
ot
exc
eed
th
e m
ax.
sa
fe s
pee
d
12
5m
m (
5”)
Max
12,0
00 RPM
