background image

SPECIFICATIONS:  
 

 

 

Floor size: 

 

21’ x 14‘’ (6.40 x 4.2m)  

   Center 

height: 

 86” 

(2.18m)

 

 

 

Weight:    

 

76.5 lbs (34.78 kg)

A

MODEL NO.  WT192114

QTY.
REQ.

DESCRIPTION

1

HSP25-213rx2

St Pole-Rear Eave Blue

Tent Fly
Panel Mesh Door

B

2

HSP25-213rx2

St Pole-Rear Eave Pink

B1

2

HSP25-213rx2,sw

St Pole-Front Eave Pink

C

1

HSP19-374rx2,sx2+HUBS

St Pole-Ridge Grey

D

2

HSP25-268rx2

St Pole-Eave Side Yellow

E

6

HSP30-177rx1,w/holes

St Pole-Main Leg

E1

4

HSP30-177rx2,sw,w/holes

St Pole-Front Room Leg

F

4

HSP19-195rx2

St Pole-Roof Corner Green

G

4

HSP19-145rx2

St Pole-Roof Middle Red

H

1

1

HSP19-285rx2,sx1+HUB

St Pole-Front Room Ridge Ivory

I

4

HSP19-120rx2

St Pole-Front Room Roof Orange

J

2

2

HSP25-150rx2,swx2

HTFWT192114
HWPWT192114-MD

Panel Mesh Wall

Panel Window Front & Rear
Panel Window Side 

2

2

5

HWPWT192114-MW

HWPWT192114-WF/R
HWPWT192114-WS

St Pole-Front Room Eave White

PART NO.

REPLACEMENT PARTS

TROUBLESHOOTING GUIDE

PROBLEM

1. CONDENSATION

2. SEAM LEAKAGE

3. MILDEW

4. REPAIRING A TEAR

5. FAULTY ZIPPER

6. FADING FABRIC

7. FLOOR CONDENSATION

This is caused by lower temperatures on the outside of the tent combined with body heat on the inside of the tent. When this occurs, avoid touching walls to reduce 
contact leakage. Leaving the doors and windows open will reduce moisture condensation. Store wet clothing outside of tent.  Not applicable to screen houses.

Apply a generous amount of seam sealer on inside seams. Seam sealer may be purchased at any local sporting goods store.

To avoid mildew, store tent/screen house ONLY when thoroughly dry. However, if mildew occurs use a soft bristle brush or sponge with mild dishwashing soap or Fels 

Naptha soap to clean. Let dry thoroughly and a tent approved water repellent compound may be applied.

For small tears use a self-adhesive patch kit. We recommend a canvas or awning repair shop for larger tears.

Zippers are self repairing. If the zipper separates, you can move the slider to the beginning of the zipper tape and rework the zipper. 

Do not leave up in direct sunlight longer than necessary. If left in sunlight for prolonged periods of time, fabric will fade and weaken.

A ground cloth under the floor helps prolong its life, provides additional insulation and moisture protection. The cloth should be smaller than the floor to prevent rain 
from running under the tent.  Not applicable to screen houses.

8. USE OF STAKES

Stakes should be installed at a 45 degree angle using a hammer or mallet. Stake loops should be kept taut without over stretching fabric or webbing. This could cause 
tears or leakage. To remove safely, use a hammer or stake puller. Do not remove by pulling on the fabric.

SOLUTION

2

2

Rope Light

HRL12’

Hub-Ridge Ends

2

1

HH PHM-327

Hub-Ridge Inner

3

2

HH PHM-325

Hub-Eave Corner

4

3&4

9

HH PHM-328

Hub-Eave Inner Door 

5&6

HH PHM-470 

1

2

Hub-Eave Inner Rear

7

HH PHM-329

Hub-Eave Outer Door

8

1

HH PHM-468 
HH PHM-469 

Hub-Eave Outer Door

10

1

HK15-26-1

Hub-Ridge Front 

11

1

HK15-155-2

Hub-Ridge Center 

12

10

HH PHM-326

Deck Feet 

 

KEY
NO.

QTY.
REQ.

DESCRIPTION

PART NO.

KEY
NO.

A

4

3

1

1

2

6

12

B1 B

C

D

E

E1

E1

E1

E1

J

H

I

F

G

10

5

8

9

11

3

4

7

A

A

7

B

B

A

B

B1

WT192114        10/18

Summary of Contents for FLAT CREEK

Page 1: ...rds which may cause harm to this product or its occupants Have a minimum of two adults for assembly During assembly poles are under tension If not held firmly in place during assembly poles could break or flip up possibly causing serious injury Safety glasses may be worn throughout the assembly process as an additional precaution Excercise care when using electric devices in and near tents 6 MONTH...

Page 2: ... each Door Panel 2 each Rope Light 2 each batteries not included 1 Assemble the roof frame as shown below matching color coded poles to color coded connectors Use the diagram below and the replacement parts listing on page 4 as reference Make certain the metal springs lock into place on all the connectors It may be helpful to layout poles and hubs matching color coding before beginning assembly 2 ...

Page 3: ...e of holes at the bottom of the pole 4 Stake the sleeve to the ground through the attached D ring 5 Inside the tent attach hook and loop fasteners along the eaves Step 6 Attach wall panel Step 5 Secure guy lines Step 7 Attach optional lights Packing the tent 1 Spread tent flat distribute evenly 2 Fold into quarters not to exceed the length of pole bag 3 Lay pole bag at opposite end from door Tight...

Page 4: ...re To avoid mildew store tent screen house ONLY when thoroughly dry However if mildew occurs use a soft bristle brush or sponge with mild dishwashing soap or Fels Naptha soap to clean Let dry thoroughly and a tent approved water repellent compound may be applied For small tears use a self adhesive patch kit We recommend a canvas or awning repair shop for larger tears Zippers are self repairing If ...

Reviews: