manualshive.com logo in svg

Oxgard Cube C-02, Installation Manuallines

The Oxgard Cube C-02 is a high-quality security device designed to protect your property. Ensure proper installation by following the detailed instructions in the Installation Manual provided. Download the manual for free from manualshive.com to easily set up and maximize the efficiency of your security system.

Share
Download
background image

 

Installation guidelines 

 15 

5. Connecting turnstile 

Connecting BP, PU, and access control is carried out with the help of 

a cross-board located in the block in barrier arms’ unit, under the removable 

cover (Fig. 8). 

For this it is required to undo 2 screws (1) and  4 screws (2), smoothly 

move  the cover up  on a short distance, without breaking the cable, 

connecting the display panel (Fig. 9). Disconnect the cable from the display 

board. 

Slide the cover to the end and make free the access to a rotary 

mechanism. Fig. 10 shows the picture after removing of the cover  

 

Fig. 8. Cross-board arrangement  

Summary of Contents for Cube C-02

































Reviews:

No comments

Related manuals for Cube C-02

Brands by name

Popular brands

Load more brands