Owon SDS1000 User Manual Download Page 7

Page: 7 / 68

2.Safety Terms and Symbols

2. Safety Terms and Symbols

Safety Terms

Terms in this manual (

The following terms may appear in this manual):

Warning:

Warning indicates conditions or practices that could result in

injury or loss of life.

Caution:

Caution indicates the conditions or practices that could result in

damage to this product or other property.

Terms on the product.

The following terms may appear on this product:

Danger:

Indicates an immediate hazard or injury possibility.

Warning:

Indicates a possible hazard or injury.

Caution:

Indicates potential damage to the instrument or other property.

Safety Symbols

Symbols on the product

. The following symbol may appear on the product:

Hazardous Voltage

Refer to Manual

Protective Earth Terminal

Chassis Ground

Test Ground

Summary of Contents for SDS1000





































































Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands

Owon SDS1000, User Manual

Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands